← PA66 AKV50H1.0 ╝PBT WF1008PC DFL146PA66ˉAKV35CXH2.0PCˉGP2300PCˉ9415(Z) PA66基础创新塑料RF0057ELCP/LX70M35H/TPUˉETE70DTP/HE-362PP/RC2472PP/SP98/FCOC APL5014DPPPˉJ460FPA6 PB320G6PP/HF3308CEVA/VE430ATPE EM550PC/MB1700PPSOX00428PA12/X7344TPU/S98ANPP 2400TPUˉ40PC/ABS NH-1017D PA66旭化成1402S LCP宝理L130-XLD2PPS/L4019POM/881SI2/ PA6三菱工程1010GN2-30PA6ˉPI001PC SC-1004APC EXL1860T LCP新石油化学MG350-PRLPP 70CSR-MPOMTR-10D POM 美国赫斯特 C9021TF PC 泰国三菱工程 HL8002 POM 工程塑料 F25-03HTPPˉBA238G3ˉPCˉNH-102PA6ˉ1330GFHPA66 FR250TPU/501ABS surface pretreatment is necessary to pre treat the plastic surface before painting, in order to improve the adhesion of the coating on the surface of the plastic and improve the appearance of the plastic. (1) when annealed plastic ABS is formed, it is easy to form internal stress and easy to crack at the stress concentration after coating. Annealing or surface treatment can be used to eliminate stress. Annealing treatment is to heat the ABS plastic molding parts below the thermal deformation temperature, that is, 60 degrees centigrade, and heat preservation 2H. In order to reduce investment in equipment, the whole surface treatment can be used to improve the surface condition. The formulation and process of the whole surface treatment are listed in Table 1. Table 1 whole surface treatment formula and process parameters / 1 water / 3 temperature / temperature / C room temperature treatment time /mi15 - 20 (2) oil removal ABS plastic parts are often contaminated with oil, hand sweat and demoulding agent, which will make the adhesion of the coating worse, the coating produces cracking, foaming and shedding. Oil removal should be carried out before coating. ABS plastic parts are usually cleaned with gasoline or alcohol and then chemical degreasing. The process formula is listed in Table 2. Table 2 the residual alkaline solution on the surface of the workpiece should be thoroughly cleaned after the process parameters of sodium hydroxide (S/L) sodium 50~70 phosphate (S/L) 20~30 sodium carbonate (S/L) 10~20 surface active agent (S/L) 5~10 temperature / 50~60 treatment time /min10 to 15 chemical oil, and cleaned with pure water ***, drying or drying. (3) electrical and dust removal plastic products are insulators, and the surface resistance is generally around 1013 ohms, which is easy to generate static electricity. After charged, it is easy to adsorb tiny dust in the air and stick to the surface. It is very difficult to remove dust from electrostatic adsorption by general blowing method. High pressure ionized air flow has good effect in addition to electrostatic precipitator.
TPV热塑性三元乙丙动态硫化弹性体/橡胶的主要性能：TPV易于焊接、可重复使用、环保。TPV热塑性三元乙丙动态硫化弹性体/橡胶的主要特点：1、优异的抗老化性能和良好的耐候、耐热性能；2、优异的抗yong久变形性能；3、优异的抗张强度、高韧性和高回弹性；4、优异的环保性能和可重复使用；5、优异的电绝缘性能；6、硬度范围广泛；7、使用温度范围广泛；8、颜色多样化，有全、半、浅色系列，着色容易，容易加工成型；9、可与PP、PA、PC‖、ABS、PS、PBT、PET等多种材料共***或挤出成型。TPV 8221-60、TPV 203-50、TPV 281-45MED、TPV 281-55MED、TPV 281-64MED、TPV 281-73MED