为了在南京NSK轴承运行中提供更好的功能，通常使用光滑润滑脂来停止光滑的轴承，这可以减少轴承的摩擦和温度。如果润滑脂发生变形，不但不能起到相关的作用，而且不利于轴承的使用，所以务必购买润滑脂。学习如何判断平滑脂肪是否能改变。
To provide better performance in Nanjing NSK bearings, ***ooth grease is usually used to stop ***ooth bearings, which can reduce friction and temperature. If the grease deformation, not only can not play a related role, but also is not conducive to the use of bearings, so be sure to buy grease. Learn how to judge whether ***ooth fat can change.
光滑脂肪的鉴定：
Identification of ***ooth fat:
1。油流观测
1. Oil flow observation
取两个量杯，一个装满光滑的油来反射南京NSK轴承，另一个空放在桌上，装满光滑的油，量杯从桌上抬起30-40厘米并倾斜，使光滑的油逐渐进入空杯，观察其活动，良好光滑的油流。ULD是细长的，平均的，连续的，如果呈现的话。油流动得非常快，非常缓慢，有时大量的油流下来，这意味着光滑的油已经改变了。
Take two measuring cups, one filled with ***ooth oil to reflect the Nanjing NSK bearing, the other empty on the table, filled with ***ooth oil, measuring cup lifted from the table 30-40 cm and tilted, so that ***ooth oil gradually into the empty cup, observe its movement, good ***ooth oil flow. ULD is slender, ***erage, continuous, if presented. Oil flows very fast, very slowly, and sometimes a lot of oil flows down, which means that the ***ooth oil has changed.
2、手捏法
2, hand kneading method
南京NSK轴承用拇指和食指揉搓光滑的油，反复擦拭。手柄光滑，碎屑少，无摩擦。如果你的手指之间有更多的摩擦，比如沙子，这意味着更光滑的油含有更多的杂质并且不能使用，新的更光滑的油应该被替换。
Nanjing NSK bearings rub the ***ooth oil with thumb and forefinger and wipe it repeatedly. The handle is ***ooth, with little debris and no friction. If you h***e more friction between your fingers, such as sand, this means that ***oother oils contain more impurities and can't be used, new ***oother oils should be replaced.
三。磨料法
Three. Abrasive method
在阴天，用螺丝刀把光滑的油提高到45度。比较阳光和油滴，南京NSK轴承你可以清楚地看到，光滑油中没有碎片是好的和可持续的。如果磨料太多，应使用光滑的油。
On cloudy days, use a screwdriver to raise the ***ooth oil to 45 degrees. Comparing sunlight with oil droplets, Nanjing NSK bearings can be seen clearly that no debris in ***ooth oil is good and sustainable. If there is too much abrasive, ***ooth oil should be used.
4。油滴***法
4. Oil droplet tracing method
取清洁的白色滤清器试纸，滴几滴油在滤清器试纸上，油面光滑渗漏，如果有黑色粉末，感觉堵塞，然后澄清光滑的油面杂质，油面光滑粉末，感觉干燥。用手和标记润滑。
Take a clean white filter test paper, drop a few drops of oil on the filter test paper, oil surface ***ooth leakage, if there is a black powder, feel blocked, and then clarify the ***ooth oil surface impurities, oil surface ***ooth powder, feel dry. Lubricate with hands and marks.
文章来自：南京SKF轴承 www.wh-
The article is from: Nanjing SKF bearing www.wh-
文章来自：南京INA轴承 a-
The article is from: Nanjing INA bearing a-
文章来自：南京NSK轴承
The article is from: Nanjing NSK bearing
***：524085168
电话：0510-81207777
手机：13311666672