如果你仔细观察镇江INA轴承轨迹，你就会知道在轴承箱中只有径向载荷、大的轴向载荷、扭矩载荷或的刚度不等式。可对滚针轴承进行检查，看它们是否增加了意外载荷，设备误差太大，以此为线索调查轴承损坏的原因。
If you look closely at the track of the Zhenjiang INA bearing, you will know that there is only radial load, large axial load, torque load or stiffness inequality in the bearing box. Needle roller bearings can be inspected to see if they h***e increased the unexpected load, equipment error is too large, as a clue to investigate the causes of bearing damage.
1。轴承清洗。
1. Bearing cleaning.
拆卸镇江INA轴承进行维修时，首先记录轴承的外观，确认润滑剂的残留量，对检查用的润滑剂进行取样，清洗轴承。***和煤油通常用作洗涤剂。轴承分别清洗、清洗和清洗。首先，将金属网垫放置在底部，这样轴承不直接接触容器中的污垢。如果轴承在清洗过程中旋转，则会损坏轴承的滚动表面。在***清洗中，用刷子清洗油脂和胶粘剂。清洗后，转为精洗。
When disassembling Zhenjiang INA bearing for maintenance, first record the appearance of the bearing, confirm the residual amount of lubricant, sample the lubricant used for inspection, and clean the bearing. Gasoline and kerosene are commonly used as detergents. Bearings are cleaned, cleaned and cleaned separately. First, the metal mesh pad is placed at the bottom, so that the bearing does not directly touch the dirt in the container. If the bearing rotates during the cleaning process, it will damage the rolling surface of the bearing. In crude oil cleaning, wash grease and adhesive with brush. After cleaning, turn to fine wash.
精细清洗是在清洗过程中仔细清洗镇江INA轴承。此外，清洁油也应保持清洁。
Fine cleaning is to carefully clean Zhenjiang INA bearings during the cleaning process. In addition, clean oil should also be kept clean.
2。轴承的维护与判断
2. Maintenance and judgement of bearings
为了确定拆卸的轴承是否可以重复使用，滚针轴承须在清洗后检查。仔细检查滚道表面、滚动表面、匹配表面状况、保持架磨损状况、轴承间隙是否增加，以及是否有损伤或异常与尺寸精度的下降有关。对于不可拆卸滚珠轴承，内圈用一只手水平支撑，外圈转动平稳。
In order to determine whether the di***antled bearing can be reused, needle roller bearings must be inspected after cleaning. Careful inspection of raceway surface, rolling surface, matching surface condition, cage wear condition, bearing clearance is increased, and whether there is damage or abnormality related to the decline in dimensional accuracy. For non detachable ball bearings, the inner ring is supported horizontally with one hand and the outer ring rotates ***oothly.
油脂太多。然后更换镇江INA轴承润滑剂。用油润滑的滚针轴承应该用新鲜油代替，如果可能的话，在排出旧油后以低速旋转几分钟。油尽可能收集残余污染物，然后清洗油。当使用润滑脂轴承代替润滑脂时，应使用约翰逊分离器，以避免与滚珠轴承棉的任何部分接触。应更加注意这个问题，特别是当使用小轴承时，因为这些残余纤维可能楔入辊子之间并造成损坏。
Too much grease. Then replace Zhenjiang INA bearing lubricant. Needle roller bearings lubricated with oil should be replaced by fresh oil and, if possible, rotate at a low speed for a few minutes after discharging the old oil. The oil can collect residual pollutants as far as possible, and then clean the oil. When grease bearing is used instead of grease, Johnson separator should be used to ***oid contact with any part of ball bearing cotton. More attention should be paid to this problem, especially when ***all bearings are used, because these residual fibers may wedge between rollers and cause damage.
在使用镇江INA轴承时，如果要保证使用，那么就要检查滚针轴承，看看它的振动和声音、温度、润滑剂状态（颜色和粘度都有变化，是否有***）。记住，润滑剂的用量须适中，浪费少，不能发挥其应有的作用，在运行过程中，不能超过极限速度，由于过热或温高和损坏，如果工作温度超过100度，应每年更换2-3次。
In the use of Zhenjiang INA bearing, if you want to ensure the use, then it is necessary to check the needle roller bearing, to see its vibration and sound, temperature, lubricant state (color and viscosity h***e changed, whether there are foreign bodies). Remember, lubricant dosage should be moderate, less waste, can not play its due role, in the course of operation, can not exceed the limit speed, due to overheating or high temperature and damage, if the working temperature exceeds 100 degrees, should be replaced 2-3 times a year.
文章来自：镇江SKF轴承 www.wh-
The article is from: Zhenjiang SKF bearing www.wh-
文章来自：镇江INA轴承 a-
The article is from: Zhenjiang INA bearing a-
文章来自：镇江NSK轴承
The article is from: Zhenjiang NSK bearing
***：524085168
电话：0510-81207777
手机：13311666672