管柱脱落是自由式管柱结构经常发生的一种现象,这是由于正常运转时转子旋转对定子产生的摩擦扭矩方向实际上是定子及油管的连接螺纹的卸扣方向,如果摩擦力矩大于油管扣的上扣扭矩,油管就脱扣。当尾管很重时,还会出现螺纹掳扣。当管柱脱落时,通过作业重新连接好就能***生产。如果未发生螺纹掳扣,可以采取对扣方式打捞,如果发生掳扣,必须下打捞工具进行打捞。Column shedding is a common phenomenon of free tube structure, which is due to the direction of rotation of the friction torque generated by the stator rotor during normal operation is actually a stator and tubing connection1 screw shackle direction, if the friction torque is greater than the pipe le on torque, oil pipe tripping. When the tail pipe is very he***y, there will also be a thread caption. When the pipe column falls off, the production can be restored by reconnecting the work. If the le is not threaded, it can be salvaged by the way of the le. If the le occurs, the fishing tool must be salvaged.
杆柱脱落Rod shedding杆柱脱落也是螺杆泵常发生的一种故障现象,表现为运行电流很低,井口也无产液,正反循环油套不连通,通过对扣或下入抽油杆打捞工具就可以进行处理来***生产。抽油杆脱落也有两种情况,一是脱扣,一是掳扣。造成脱扣的原因是停机后抽油杆柱扭转变形余能释放引起杆柱反转,可以采取在地面和抽油杆柱上安装防倒装置进行防止。造成杆柱掳扣的原因有三个:一个是稠油井在长时间关井后再启泵时,启动扭矩特别大,把螺纹损坏了;一个是油特别稠,螺杆泵长期在高扭矩下工作而把螺纹损坏;再有一个原因是定子部分脱胶,转子转不动造成的。

A、定子A, stator定子是螺杆泵的一个关键部件,并直接影响到井下机组的寿命。定子制造质量越高,井下机组的寿命就越长。定子的作用就是提供转子工作和液体抽汲的螺旋腔,其结构非常简单,由钢制外壳和塑料/橡胶衬套内腔有双螺旋、三螺旋、四螺旋甚至五螺旋、六螺旋,在相同尺寸下,螺旋数越多,泵的排量越高。The stator is a key component of the screw pump, which directly affects the life of the downhole unit. The higher the quality of the stator, the longer the life of the downhole unit. The role is to provide a rotor stator and liquid pumping spiral c***ity drain, the structure is very simple, a steel shell and a plastic / rubber bushing c***ity with double helix, three helix, four or even five, six spiral helical spiral, in the same size, the number of spiral, the displacement of the pump is high.

E、抽油杆扶正器E, sucker rod centralizer抽油杆扶正器由心轴和扶正筒组成,它接在两根抽油杆之间,被卡在两个抽油杆接箍之间。心轴也就是一要极短的抽油杆短节。扶正筒是一个内孔比心轴大1MM左右的空心塑料筒,外部有四个略比油管内径小的扶正翼,采取浇注成型。扶正筒可以围绕心轴转动,防止抽油杆旋转时与内壁接触而磨蚀油管,又可以让流体通过。The sucker rod centralizer is composed of the heart shaft and the upright cylinder, which is connected between the two sucker rods and is stuck between the two sucker rod hoops. The axis of the heart is also an extremely short rod short section. The centering cylinder is a hollow plastic tube inner hole Bixin shaft around 1MM, external four slightly ***aller than the diameter of the tubing centralizer wing, adopt casting. The centralizer can revolve around the axis to prevent the sucker rod from touching the inner wall when it rotates, and it can also let the fluid pass through.