仔细检查镇江SKF轴承座、轴和密封轴承结构，确保工作面清洁良好，特别是检查螺纹孔、管道或油箱，防止加工残留物。铸造轴承块应确保没有砂芯砂留在一些未加工表面和所有毛刺实现。
Check the structure of Zhenjiang SKF bearing base, shaft and seal bearing carefully to ensure that the working face is clean and good, especially check the threaded hole, pipeline or oil tank to prevent processing residue. The casting bearing block should ensure that no sand core sand remains on some unmachined surfaces and all burrs are achieved.
从轴承结构各部分的尺寸和形状来看，相关部件须满足精度要求，满足公共服务范围的要求，才能发挥其应有的功能。圆柱体轴颈和孔的直径通常以微米或微米的两部分和四个不同的位置测量。镇江SKF轴承轴颈的锥度可通过环规、特殊锥度或正弦杆测量。
From the dimension and shape of each part of the bearing structure, the relevant components must meet the accuracy requirements, meet the requirements of the scope of public service, in order to play its due function. The diameter of the cylinder journal and hole is usually measured in two parts of micron or micron and four different positi***. The taper of Zhenjiang SKF bearing journal can be measured by ring gauge, special taper or sine bar.
建议保留相关的观测和测量资料以供参考。在测量中，零件和测量仪器应保持在近似相同的温度，以确保测量的准确性。这意味着零件和测量设备可以长时间放置在同一位置，以达到相同的温度。这种做法对于大型轴承和相关部件尤其重要。
It is suggested that relevant observati*** and measurements should be retained for reference. In measurement, parts and measuring instruments should be kept at approximately the same temperature to ensure the accuracy of measurement. This means that parts and measuring equipment can be placed in the same location for a long time to achieve the same temperature. This practice is especially important for large bearings and related components.
轴承应保持在原来的包装中，直到设备出现防止灰尘和其余污染物进入。一般来说，在离开工厂之前，不必除去应用于轴承的防锈剂。只需清洗镇江SKF轴承的内外孔即可。但是，如果轴承是用油润滑的，并且在非常高或非常低的温度下使用，或者如果所有的润滑脂和锈都不相容，在安装前要仔细清洁和干燥，以防止损坏轴承润滑脂。
Bearings should be kept in the original packaging until the equipment appears to prevent dust and other contaminants from entering. Generally speaking, it is not necessary to remove the rust inhibitor applied to bearings before le***ing the factory. Just clean the inside and outside holes of Zhenjiang SKF bearing. However, if the bearing is lubricated with oil and used at very high or very low temperatures, or if all grease and rust are incompatible, carefully clean and dry before installation to prevent damage to the bearing grease.
如果轴承因操作不当而被污染，则须在安装前清洗和干燥。
If the bearing is contaminated due to improper operation, it must be cleaned and dried before installation.
从原包装上拆下轴承。如果防锈剂的表面粘度更厚或更高，则轴承的清洗和干燥要求是相同的。当直径大于420毫米的镇江SKF轴承非常大时，这可能发生，并可用于除去溶剂或石蜡油。
Remove the bearings from the original package. If the surface viscosity of the rust inhibitor is thicker or higher, the bearing's cleaning and drying requirements are the same. This may occur when Zhenjiang SKF bearings larger than 420 mm in diameter are very large and can be used to remove solvents or paraffin oil.
如果使用带有密封或密闭的轴承，在安装前不要清洗它，因为在制造过程中它已经充满油脂。
If a bearing with a seal or seal is used, do not clean it before installation because it is already full of grease during manufacture.
文章来自：镇江SKF轴承 www.wh-
The article is from: Zhenjiang SKF bearing www.wh-
文章来自：镇江INA轴承 a-
The article is from: Zhenjiang INA bearing a-
文章来自：镇江NSK轴承
The article is from: Zhenjiang NSK bearing
***：524085168
电话：0510-81207777
手机：13311666672