了解镇江SKF轴承的润滑也须知道超载会影响轴承的状态，为轴承传动，工作负荷不稳定，经常超载的现象，如果没有适当的保护措施，将导致重载齿断裂，或长T，吃。牙齿的根部会产生大量的疲劳裂纹和断裂。因此，我们须定期维护和维护工作。
To understand the lubrication of Zhenjiang SKF bearings, it is necessary to know that overload will affect the state of bearings. It is a phenomenon of bearing tran***ission, unstable work load and frequent overload. If there is no proper protection measures, it will lead to the fracture of overloaded teeth, or long T, eat. The root of the tooth will produce a lot of fatigue cracks and fractures. Therefore, we need regular maintenance and maintenance work.
首先，我们关注镇江SKF轴承润滑非正常的原因。润滑非正常的原因很多。高速重载轴承，润滑非正常会导致局部的齿面过热，导致颜色的变化，结合其余故障。润滑非正常的原因很多。除油通道和喷嘴堵塞，可怜的齿面润滑可以通过进水引起的，和润滑油温度过高的恶化。
First of all, we are concerned about the abnormal reason of SKF bearing lubrication in Zhenjiang. There are many reas*** for the abnormal lubrication. High-speed and he***y-duty bearings, abnormal lubrication will lead to local tooth surface overheating, resulting in color changes, combined with other failures. There are many reas*** for the abnormal lubrication. Except for blocked oil passages and nozzles, poor tooth surface lubrication can be caused by water intake and deterioration of excessive oil temperature.
推力球轴承的安装有两个关键点。一是控制笼子和球的质量。另一种是在装配后对轴承名义高度T的控制。此外，环和阀座环可以彼此分离，导致管理上的问题，那就是，为了避免混乱，进口轴承组件。冲压模具采用弯曲边安装模具。冲压后，镇江SKF轴承球要滚进袋敏锐，但不能灌入袋内，并有检查球的运动包技术***。如果实体保持架压得太深，球的运动将非常小，与印记的亮点和笼子太小的压印接触不够强。
There are two key points in the installation of thrust ball bearings. One is to control the quality of cage and ball. The other is the control of the nominal height T of the bearing after assembly. In addition, the rings and seat rings can be separated from each other, leading to a management problem, that is, to ***oid confusion, import bearing assemblies. The stamping die is installed on the bending edge. After stamping, Zhenjiang SKF bearing ball should be rolled into the bag keen, but can not be poured into the bag, and there are technical regulati*** for checking the ball sports bag. If the solid cage is pressed too deep, the movement of the ball will be very ***all, not strong enough to touch the highlights of the mark and the imprint that the cage is too ***all.
在轴承的应用中，每个人都知道合理的润滑是工作中重要的过程。如果没有合理的润滑，会对轴承产生非正常影响。严重的情况将直接导致轴承的实际性性。今天，我们描述了润滑非正常的影响镇江SKF轴承，以帮助您避免类似的情况下，在日常使用的轴承。
In the application of bearings, everyone knows that reasonable lubrication is an important process in the work. If there is no reasonable lubrication, it will h***e an abnormal effect on the bearing. Serious conditi*** will directly lead to the practicality of bearings. Today, we describe the abnormal effects of lubrication on Zhenjiang SKF bearings to help you ***oid similar situati*** in daily use.
内径和小推力球轴承座的座环很小，有两组之间差异无统计学意义。为了避免一组混合轴承，也就是说，被困在轴承中的一组陶瓷套筒是阀座环或所有环。通常，吸环和座组由辅助工具区分，或内部校准采样在标称高度之前检查内径塞规。为了方便地检查内径，阀座环被降低，轴环被放置在顶部。如果内阁直径明显淬火，加热，氧化，就不需要校准的内径，可见轴和阀座环不易混合。在安装镇江SKF轴承推力球轴承后，需要测量标称高度T，并进行确认。
The seat ring of the inner diameter and the ***all thrust ball bearing seat is very ***all, and there is no significant difference between the two groups. To ***oid a group of hybrid bearings, that is, a group of ceramic sleeves trapped in the bearing are seat rings or all rings. Usually, suction rings and seat groups are distinguished by auxiliary tools, or internal calibration sampling checks the inner diameter plug gauge before nominal height. In order to check the inner diameter conveniently, the seat ring is lowered and the collar is placed at the top. If the cabinet diameter is ***iously quenched, heated, and oxidized, there is no need to calibrate the inner diameter, visible shaft and seat ring are not easy to mix. After installing Zhenjiang SKF bearing thrust ball bearing, we need to measure the nominal height T and confirm it.
文章来自：镇江SKF轴承 www.wh-
文章来自：镇江INA轴承 a-
文章来自：镇江NSK轴承
***：524085168
电话：0510-81207777
手机：13311666672