杆端关节泰州SKF轴承的温度可以通过杆端关节轴承腔室外的温度来计算。采用油孔法直接测量杆端关节轴承外圈温度更为合适。通常，杆端关节轴承的温度随着杆端关节轴承的运行而缓慢升高，1-2小时后达到稳定状态。
The temperature of Taizhou SKF bearing with rod end joint can be calculated by the temperature outside the chamber of the rod end joint bearing. It is more suitable to directly measure the outer ring temperature of rod end joint bearing by oil hole method. Generally, the temperature of the rod-end joint bearing increases slowly with the operation of the rod-end joint bearing, and reaches a stable state after 1-2 hours.
杆端关节轴承室温随机化器的热容、散热、速度和载荷发生变化。如果润滑和安装部件合适，杆端关节轴承的温度将急剧上升，并且会发生异常高温。此时，必*须停止操作，并且必*须采取必要的预防措施。
The heat capacity, heat dissipation, speed and load of the room temperature randomizer for rod-end joint bearings change. If the lubrication and installation parts are suitable, the temperature of the rod end joint bearing will rise sharply, and abnormal high temperature will occur. At this point, the operation must be stopped and necessary precauti*** must be taken.
该温度传感器可随时监测杆端关节泰州SKF轴承的工作温度。当温度超过规定值时，可实现自动报*警或停车，防止轴烧事故。
The temperature sensor can monitor the working temperature of Taizhou SKF bearing at any time. When the temperature exceeds the prescribed value, automatic alarm or parking can be realized to prevent shaft burning accidents.
高温常被用来表示杆端关节轴承处于异常状态。高温对杆端关节轴承的润滑剂也是***的。杆端关节轴承的过热有时可归因于杆端关节轴承的润滑剂。如果连杆接头轴承的温度超过125℃，则会降低连杆接头泰州SKF轴承的使用寿命。高温杆端关节轴承的原因包括：
High temperature is often used to indicate that the rod end joint bearing is in abnormal condition. High temperature is also harmful to the lubricant of rod-end joint bearings. The overheating of rod-end joint bearings can sometimes be attributed to the lubricant of rod-end joint bearings. If the temperature of the connecting rod joint bearing exceeds 125 C, the service life of the connecting rod joint Taizhou SKF bearing will be reduced. Reas*** for high temperature rod end joint bearings include:
1。润滑不足或过度润滑。
1. Insufficient or excessive lubrication.
2。含杂质，过载，杆端关节轴承断环，间隙不足。
2. Containing impurities, overload, broken ring of rod end joint bearing, insufficient clearance.
三。油封等引起的高摩擦。
Three. High friction caused by oil seal, etc.
因此，无论是对杆端关节轴承本身还是其*他重要部件的温度测量，都需要对杆端关节的温度进行连续监测。如果操作条件保持不变，任何温度变化都可能指示故障。
Therefore, it is necessary to continuously monitor the temperature of the rod-end joint whether for the temperature measurement of the rod-end joint bearing itself or other important components. If the operating conditi*** remain unchanged, any temperature change may indicate failure.
杆端关节泰州SKF轴承的周期性温度测量可以帮助温度计，如数字温度计，精*确测量杆端关节轴承的温度，并以摄氏度或华氏度显示。
Periodic temperature measurement of Taizhou SKF bearing with rod end joint can help thermometers, such as digital thermometers, accurately measure the temperature of rod end joint bearing and display it in degrees Celsius or Fahrenheit.
重要杆端连接轴承是指设备损坏时停机。因此，对于这种杆端关节轴承，**好安装温度检*测器。通常，杆端关节轴承在刚刚润滑或重新润滑后温度自然升高，并持续一至两天。
Important rod end connection bearings refer to shutdown when equipment is damaged. Therefore, for this kind of rod-end joint bearing, ** install temperature detector. Usually, the temperature of rod-end joint bearings increases naturally after just lubricating or re-lubricating and lasts for one to two days.
文章来自：泰州SKF轴承 www.wh-
Article from: Taizhou SKF Bearing www.wh-
文章来自：泰州INA轴承 a-
Article from: Taizhou INA Bearing a-
文章来自：泰州NSK轴承
Article from: Taizhou NSK Bearing
***：524085168
电话：0510-81207777
手机：13311666672/13395185757