轴承油的润滑管理是非常重要的，不容忽视。
The lubrication management of bearing oil is very important and should not be neglected.
超过一半的机械故障或早期磨损是由于润滑技术的管理。润滑管理的主要任务是防止轴承、齿轮等摩擦运动部件的磨损或烧结，防止和减少磨损，减少摩擦，防止设备事故，提高泰州INA轴承设备生产效率，节约能源，提高能源利用率。经济效益。
More than half of mechanical failures or early wear are due to the management of lubrication technology. The main task of lubrication management is to prevent wear or sintering of friction moving parts such as bearings and gears, prevent and reduce wear, reduce friction, prevent equipment accidents, improve production efficiency of INA bearing equipment in Taizhou, s***e energy and improve energy utilization. Economic performance.
1。润滑管理是一项专*业的技术管理。专职润滑技术管理人员应建立润滑管理体系，培养润滑技术知识。
1. Lubrication management is a technical management of a specialized industry. Full-time lubrication technical management personnel should establish lubrication management system and cultivate lubrication technical knowledge.
2。在合理容积的前提下，有利于排气、除尘、水分离和油温的降低。
2. On the premise of reasonable volume, it is conducive to exhaust, dust removal, water separation and oil temperature reduction.
三。定期对油样进行取样和运输。对油的气味、颜色、粘度、含水率、水分离性能、污染物类型和含量、防泡沫性能进行了测试。当进入润滑点的油中水分含量超过0.1个百分点时，机械磨损急剧增加；当水分含量超过0.5个百分点时，泰州INA轴承润滑条件将非常***。做一个好的测试记录。
Three. Oil samples are sampled and transported regularly. The odor, color, viscosity, moisture content, water separation performance, pollutant type and content, and anti foam performance of the oil were tested. When the moisture content in the oil entering the lubrication point exceeds 0.1%, the mechanical wear increases sharply; when the moisture content exceeds 0.5%, the lubrication condition of Taizhou INA bearing will be very dangerous. Make a good test record.
4。分析比较试验记录，预测不*良润滑条件，制定改进措施或预防措施。该系统油位、油质、油温、油压控制报*警联锁安*全可靠，防止了润滑事故的发生。
4. Analysis and comparison of test reco***, prediction of poor lubrication conditi***, formulation of improvement measures or preventive measures. The oil level, oil quality, oil temperature, oil pressure control report, alarm interlocking security of the system are safe and reliable, which prevents the occurrence of lubrication accidents.
更换钢轮泰州INA轴承漏油密封的具体步骤如下：
The concrete steps for replacing the oil leakage seal of Taizhou INA bearing of steel wheel are as follows:
1。松开振动马达的四个固定螺栓并拆下振动马达（不拆下马达上的橡胶软管）。
1. Loosen the four fixed bolts of the vibration motor and remove the vibration motor (without removing the rubber hose on the motor).
2。松开马达座上的七个螺栓并拆下马达座。
2. Loosen the seven bolts on the motor seat and remove the motor seat.
三。松开支撑板和滑动轴承座上的八个固定螺栓，以及连接支撑板和前框架的螺栓。减震器由支撑板支撑。
Three. Loose the eight fixed bolts on the support plate and sliding bearing seat, and the bolts connecting the support plate and the front frame. The shock absorber is supported by a support plate.
4。松开轴承挡板上的八个固定螺栓，拆下挡板。
4. Loosen the eight fixed bolts on the bearing baffle and remove the baffle.
5。找到小于轴承内圈直径的垫圈，并将它们放置在外泰州INA轴承座的轴头上。
5. Find washers ***aller than the diameter of the inner ring of the bearing and place them on the axle head of the outer Taizhou INA bearing seat.
6。拆卸左盖并将靠背放置在垫板上。找到七个M12* 70螺栓拧紧左盖和运行轴承座。
6. Remove the left cover and place the backrest on the cushion plate. Find seven M12* 70 bolts to tighten the left cover and run the bearing seat.
7。通过按对角线顺序锁住7个螺栓，可将行走轴承座和轴承一起拉出。转动活动轴承座后，可更换180－220骨架油封。
7. By locking seven bolts in diagonal order, the walking bearing seat and the bearing can be pulled out together. After rotating the movable bearing seat, the 180-220 skeleton oil seal can be replaced.
根据各部件的拆卸顺序，应注意反演顺序。黄油适用于骨架油封、驱动轴承座和外轴承座，避免油压过程中油封损坏，又导致漏油。
According to the disassembly sequence of each component, attention should be paid to the inversion sequence. Butter is suitable for skeleton oil seal, drive bearing seat and external bearing seat to ***oid oil seal damage and oil leakage during oil pressure process.
文章来自：泰州SKF轴承 www.wh-
Article from: Taizhou SKF Bearing www.wh-
文章来自：泰州INA轴承 a-
Article from: Taizhou INA Bearing a-
文章来自：泰州NSK轴承
Article from: Taizhou NSK Bearing
***：524085168
电话：0510-81207777
手机：13311666672/13395185757