平齐隔膜中、高压型压力变送器YS2PB
flat-diaphragm middle、high pressure type
产品概述
本公司生产的YS2PB 系列齐平膜压力变送器选用国际***公司高精度、高稳定性压力传感器组件,经过高可靠性的放大电路及精密温度补偿,将被测介质的压力转换成4~20mA、1~5VDC等标准电信号。该产品能够***大限度的满足工业范围内多种流体介质的测量要求,适用于与各种测量控制设备配套使用。
General
The type of YS-2 flat-diaphragm pressure tran***itter has high precision,high stable pressure sensor accessory,transforms pressure of media to 4~20mA、1~5VDC .etc electric signals ,through reliable magnifying circuit and temperature compensation. It could be applied in measuring many liquid media in industrial field,which could meet requirement of user farthest,in particular suitable for multiplicate equipments.
产品特点
● 小体积、高性价比、高稳定性、高灵敏度
● 不锈钢隔离膜片及全焊接结构
● 变送器具有密封的全天候特种结构,防护等级达到IP65。
● 电防护标准:反极性保护、短路保护
● 平齐式隔膜SUS316L、根据现场工作情况,隔膜体内填充相应的工作液,可测量与SUS316L 材质兼容的气体和粘稠性液体;
● 填充液:硅油、氟油;
Features
● Compact design,cheap but high quality,high stability and sensitivity
● Stainless steel isolated diaphragm and full welding structure
● special sealing facility, and the protection class can be up to IP65
● Electrical protection standard: reverse polarity ,short circuit.
● In respect of flat diaphragm SUS316L,fill liquid to measure the gas and viscous liquid which is compatible to SUS316L.
● Liquid filling: silicone , fluorin oil.
产品应用
● 平膜、无腔、防堵塞,可测量粘稠易结晶性液体
● 专门用于测量***制造、食品加工、流程工业和造纸工业等方面;
Application
● Flat diaphragm,nocapsule,jam-proof,viscousand crystal liquid to be measured.
● Specially measure in the field pharmacy,food ,flow and paper making. etc
性能Performance
量程(bar)Range: 40、60、100、160、250、400bar
过载能力 Overload :1.5倍满量程压力 150% of full scale
压力类型Type of pressure :表压gauge pressure
测量介质media :与 316不锈钢兼容的各种液体、气体 Liquid ,gas which is compatible to SUS316 stailess steel
***度 Accuracy: 1.0、0.5级包括非线性、重复型、迟滞性在内的综合误差 containing non-linear,repeated,lagged error
长期稳定性Long stability: 典型:&plu***n; 0.2%FS Standard : &plu***n; 0.2%FS
***大: Maximum &plu***n; 0.25%FS/1
工作温度 Working temperature: -20~80℃贮存温度 Storage temperature -30~90℃
相对湿度 Relative humidity:小于 90%(30℃)less than 90%(30℃)
供电电源 Power supply :17-30V.DC(24 VDC)
信号输出 Output signal :4~20mA.DC 1~5V.DC
传输方式 tran***itting:二线 Two-line 三线 Three-line
负载电阻 Load resistance :≤(U-12)/0.02 Ω ≤(U-17)/0.02 Ω
外壳防护Enclosure protection :IP65
过程连接 Process connection :G1/2“、G3/4“、G1“阴螺纹 female thread
电气连接Electrical connection:专用插头座 (DIN43650)(DIN43650)special socket(DIN43650)
结构材料 Materials: 螺纹接口及壳体 Socket and case SUS304 Stainless steel SUS304
O形圈O ring 氟橡胶 Fluorin rubber 接液膜片Sensor diaphragm
SUS316LChinaware/SUS316L 橡胶套管rubber bushing
***橡胶 buna
外形结构(单位: mm)Structure(unit:mm)
小隔膜尺寸Diaphragm dimension
电器连接方法( GDM3009 接插件)
使用与校准
1、安装与接线(见图)
各种类型的压力变送器均可直接接在检测系统的接口上,标准螺纹为M20 × 1.5 阳螺纹。
24VDC 电源通过屏蔽电缆给变送器供电(请注意防水),“+”接24VDC 正极,“-”输出4 - 20MA 电流给 取样电阻
2、使用
变送器接线如图所示,联线正确即可使用。
Electrical connetion (GDM3009 plug-in package)
Using and calibration
No.1 mounting and connecti***(as picture shown)
All kinds of pressure tran***itter will be connected directly to test system,with standard male thread M20 × 1.5.
Tran***itter is supplied Power 24VDC by shielding cable(water-proof),with anode 24VDC connected and 4-20MA for resistance.
No.2 Application
As is shown in wiring diapram, using in correct connection.
注意事项
1、变送器是使用带膜片的进口传感器,切勿用任何物体接触膜片,以免造成***性损伤而损坏传感器。在介质温度太高(> 80℃)时,应加装散热器以保证测量精度.
2、安装时请用***工具进行安装、
3、变关器的校准应在加电5分钟后进行.并注意当时的环境温度.变送器不要随意开盖以免受潮,且变送器壳体及导线屏蔽层应牢固接地避免干扰及雷击。
4、电源应当使用带有隔离的仪表电源避免工业电源串扰,特别慎用开关电源容易自激损坏变送器。电源及信号输出应采用屏蔽电缆传输并压紧进线螺母,以保证气密性。依***标准变送器每6 个月应校准一次。
5、外配雷击管只能抗3A 冲击电流,应并联在+、- 极之间。如果打穿,请更换该无件。
备注
用户选型时请告知使用环境和安装方式,如对型号命名不清楚时可用文字说明,接口螺纹可根据要求单独设计。
Note:
No.1 Tran***itter is hse the sensor with diaphragm ease note that anything is prohibited to touch diaphragm,protecting against destroying for ever.Add the radiator when temperature is over 80℃.
No.2 Installation under the instruction of skilled worker.
No.3 Calibrate the tran***itter should be five minutes later when power is supplied and be aware of environment temperature. It can not be opened case so as to keep se and leads will be connected to earth ***oiding disturbing and lightning strike.
No.4 Using gauge power with isolation to ***oid industrial power disturbing,not using switch power at discretion,which can destroy tram***itter.Power and output signal will shield cable tran***itting and press nuts cording to national standard ,it will be calibrated once six months
No.5 lighting-strike pipe can stand 3A current between anode and cathode .If it is broken,please instead .
Remark
Please inform working environment and mounting on type selection. We could help select model and design the thread for clients.
产品详细资料请点击:S.YS2PB 平齐隔膜中高压型变送器.pdf
变送器、压力变送器、隔膜压力变送器YS2PB