在使用徐州SKF轴承电机2000小时后应清洗电机并上油。轴承有两种清洁方法：
After using Xuzhou SKF bearing motor for 2000 hours, the motor should be cleaned and oiled. There are two cleaning methods for bearings:
1。热油清洗法由于长期使用，软油或干油或防锈膏硬化的轴承，应浸入100-200摄氏度的油中，用钳子夹住轴承，刷上轴承上的油污。软油或防锈膏在加热到100-200摄氏度的定义下熔化：材料在从固体变为液体的过程中很容易被冲出轴承间隙。有时只需要在油中摇动轴承几次。油也会流过裂缝。
1. Hot oil cleaning method because of long-term use, soft oil or dry oil or rust-proof paste hardened bearings, should be immersed in 100-200 degrees Celsius oil, clamp the bearings with pliers, brush the oil stain on the bearings. Soft oil or antirust paste melts under the definition of heating to 100-200 degrees Celsius: materials can easily be washed out of bearing clearance in the process of changing from solid to liquid. Sometimes it only needs to shake the bearing several times in the oil. Oil also flows through cracks.
清洗旧电机或徐州SKF轴承进口电机向心球轴承时，应将球、球架、内环水平旋出外圈，然后浸入热油中。清洗短圆柱滚子轴承时，滚子、机架、内外环也应分开。
When cleaning the centripetal ball bearing of the old motor or Xuzhou SKF bearing imported motor, the ball, the ball rack and the inner ring should be rotated horizontally out of the outer ring and then immersed in hot oil. When cleaning short cylindrical roller bearings, the rollers, racks, inner and outer rings should also be separated.
在热油清洗中，机油温度不应超过20摄氏度。在大多数情况下，轴承疲劳损伤会导致轴承疲劳损伤。一般来说，轴承疲劳损伤造成的损伤只有三分之一来自润滑不顺畅，三分之一来自污染物进入轴承或安装和处理不当。然而，这些类型的损坏都是与工业轴承无关的精细零件，所以在使用高性能徐州SKF轴承时要小心，即使使用不当，也不能达到预期的性能效果，而且容易造成轴承损坏。
In hot oil cleaning, the oil temperature should not exceed 20 degrees Celsius. In most cases, bearing fatigue damage will lead to bearing fatigue damage. Generally speaking, only one third of the damage caused by bearing fatigue damage comes from poor lubrication, and one third comes from the incorrect entry of pollutants into the bearing or the improper installation and treatment. However, these types of damages are all fine parts unrelated to industrial bearings, so be careful when using high-performance Xuzhou SKF bearings, even if used improperly, it can not achieve the desired performance results, and easy to cause bearing damage.
2。为了检查轴承损坏情况，我们可以发现，在大多数情况下，这可能导致轴承损坏。一般来说，轴承疲劳损伤造成的损伤只有三分之一来自润滑不顺畅，三分之一来自污染物进入轴承或安装和处理不当。
2. In order to check the bearing damage, we can find that in most cases, this may lead to bearing damage. Generally speaking, only one third of the damage caused by bearing fatigue damage comes from poor lubrication, and one third comes from the incorrect entry of pollutants into the bearing or the improper installation and treatment.
这些徐州SKF轴承类型的损坏都是精细零件，与工业轴承无关，所以使用高性能轴承时要小心，即使使用不当，也不能达到预期的性能效果，而且容易造成轴承损坏。然后将轴承放入干净的煤油中，用软刷清洗，球和缝隙中的油脂和污垢用***清洗一次，再用干净的纸清洗。在清洗向心球轴承和短圆柱滚子轴承时，应将球、球架、内环和外圈分开清洗。
These Xuzhou SKF bearing types of damage are fine parts, and h***e nothing to do with industrial bearings, so be careful when using high-performance bearings, even if improper use, can not achieve the desired performance results, and easy to cause bearing damage. Then the bearings are put into clean kerosene, cleaned with a soft brush, grease and dirt in the balls and crevices are cleaned with gasoline once, and then cleaned with clean paper. When cleaning centripetal ball bearings and short cylindrical roller bearings, the ball, ball rack, inner ring and outer ring should be separately cleaned.
文章来自：徐州SKF轴承 www.wh-
文章来自：徐州INA轴承 a-
文章来自：徐州NSK轴承