 | | |  |  | Virtual 360° view |  | Pdf in Reserved Area |  | Multimedia in Reserved Area |
|
Features Gear pumps and motors built in three pieces with an extruded body in high resistance aluminium alloy.
The wide choice of shafts, flanges and ports, in compliance with all international standards (SAE, DIN
and EUROPEAN) allow for their use in an infinite variety of applications.
Displacements from 0.07 in³/rev (1,07 cm³/rev) to 5.56 in³/rev (91,10 cm³/rev) available in groups 10, 20 and 30
Max. peak pressure up to 4350 psi (300 bar)
Max. speed up to 4000 min-1 - High efficiencies
- Integrated outboard bearings for heavy
duty applications - Multiple units available in standard version,
common inlet and separated stages - Electro-hydraulic fan drive system
- Custom design
| Built-in valves - Anti-cavitation valves
- Maximum pressure relief valves
- Priority valves
- “Load sensing” priority valves
- By-pass electric valves
- Proportional relief valves
- Reverse valves
|
| | | 
 | | |  | | Virtual 360° view |  | Other informations |
|
Features Gear pumps built in three pieces with an extruded body in high resistance aluminium alloy. WHISPER is a new and original technology protected by international patents and applied to a family of external gear pumps and motors that feature low noise emissions.
The wide choice of shafts, flanges and ports, in compliance with all international standards (SAE, DIN and EUROPEAN) allow for their use in an infinite variety of applications.
Displacements from 0.07 in³/rev (1,12 cm³/rev) to 5.91 in³/rev (96,85 cm³/rev) available in groups 10, 20 and 30
Max. peak pressure up to 4350 psi (300 bar)
Max. speed up to 4000 min-1 - High efficiencies
- Low noise emission
- Integrated outboard bearings for heavy duty applications
- Multiple units
- Custom design
|
|
铸铁体液压齿轮泵及马达 | Cast iron body hydraulic gear pumps and motors |
| | Features Gear pumps and motors built in three pieces with cast iron body.
The new gear pumps and motors "PH" series is an evolution of the "POLARIS" series.
"POLARIS PH" has a new body made of cast iron to have higher operating parameters and keep the full POLARIS versatility regarding shafts, flanges, ports and built-in valves.
This project is targeted for forklifts, skid steer loaders and all those applications where traditional aluminium pumps are being pushed close to their limits.
The possibility to mate the body with the cast iron covers further reduces noise levels, in addition to increasing strength. Displacements from 1.16 in³/rev (19,09 cm³/rev) to 2.01 in³/rev (33,03 cm³/rev)
Max. peak pressure up to 4350 psi (300 bar)
Max. speed up to 3500 min¹ - High working pressure also for high displacements
- Long service life
- Low noise level
- High volumetric efficiency also at high temperature
- Inlet & Outlet optimization – High speed
- Combination in multiple pumps
- Built-in Valves simplify circuit design
| Built-in valves - Anti-cavitation valves
- Maximum pressure relief valves
- Priority valves
- “Load sensing” priority valves
- By-pass electric valves
- Proportional relief valves
- Reverse valves
|
| | |  | | |  | | Virtual 360° view | | Pdf in Reserved Area |
 | | Pdf in Reserved Area |
|
Features Gear pumps and motors made of cast iron in two pieces.
A rigid and compact structure that makes it possible to incorporate a number of functions in a limited space.
Wide range of displacements: from 0.30 in³/rev (4,95 cm³/rev) to 9.20 in³/rev (150,79 cm³/rev) available in groups 20, 30 and 40
Max. peak pressure up to 4785 psi (330 bar)
Max. speed up to 4000 min-1 - High operating pressures
- High efficiency at high temperature
- Low noise emission
- Exceptional working life expectancy
- Solid and compact design
- Custom design
| Built-in valves - Antishock and anti-cavitation valves
- Priority valves
- “Load sensing” priority valves
- By-pass electric valves
|
| | |  | | |  | | Virtual 360° view | | Pdf in Reserved Area |
| | pdf in
Reserved Area |
|
Features Gear pumps made of cast iron in two pieces.
Ideal for truck application.
Displacements from 0.50 in³/rev (8,26 cm³/rev) to 9.20 in³/rev (150,79 cm³/rev) available in groups 20, 30, 35 and 40
Max. peak pressure up to 4713 psi (325 bar)
Max. speed up to 3000 min-1 - High performance also at very low speed
- Different ports position availability
- Low noise emission
- Shaft seal system no leakage guarantee
- Modular design
- Direct mounting on the PTOs
|
| | |  | | |  | | Virtual 360° view | | Pdf in Reserved Area |
|
Features Gear pumps and motors made of cast iron in three pieces.
An extremely versatile and reliable design, also in the most extreme operating conditions.
Displacements from 1.05 in³/rev (17,28 cm³/rev) to 7.66 in³/rev (125,63 cm³/rev) available in groups 30 and 35
Max. peak pressure up to 4640 psi (320 bar)
Max. speed up to 3000 min-1 - Wide range of drive shafts and flanges in SAE version
- More choices of port locations
- Integrated outboard bearings for heavy duty applications
- Multiple units available in standard version, common inlet and separated stages
- Exceptional working life expectancy
|
内置阀门的液压齿轮泵和马达 | Built-in valves for hydraulic gear pumps and motors |
| | | | | BUILT-IN VALVES | | Pdf in Reserved Area |
|
Features Anti-cavitation valves, maximum pressure relief valves, priority valves and “load sensing” priority valves built in the following series of gear pumps and motors: POLARIS, WHISPER, KAPPA, New KAPPA Compact - Reduced overall dimensions
- Simplified plant design
- Wide choices of ports position
|
|
|
齿轮流量分配器
| | Features Gear flow dividers made of high resistance aluminium alloy.
These components can be used as flow equalizers, flow dividers and pressure intensifiers.
Displacements from 0.13 in³/rev (2,14 cm³/rev) to 2.01 in³/rev (33,03 cm³/rev) available in groups 10 and 20
Max. peak pressure up to 4060 psi (280 bar) - Modular design
- Accurate division of flow
- Built-in relief valves
- Combinations between different groups
|
| | | | | | | | Pdf in Reserved Area |
|
Features Gear flow dividers made of cast iron.
These components can be used as flow equalizers, flow dividers and pressure intensifiers.
Displacements from 1.05 in³/rev (17,28 cm³/rev) to 7.66 in³/rev (125,63 cm³/rev) available in groups 30 and 35
Max. peak pressure up to 4640 psi (320 bar) - Modular design
- Accurate division of flow
- High flow
- Combinations between different groups
|
|
|
固定排量轴向柱塞泵和马达
| Fixed displacement axial piston pumps and motors |
| |  | | |  | | Virtual 360° view | | Pdf in Reserved Area |
|
Features Fixed displacement bent axis piston pumps.
STRADA pumps are ideally suited for PTOs applications in vehicles.
Displacements from 2.49 in³/rev (40,9 cm³/rev) to 6.71 in³/rev (110 cm³/rev) available in groups 32 and 37.
Max. peak pressure up to 5800 psi (400 bar)
Max. speed up to 2950 min-1 - Low noise level
- Direct mounting on the PTOs
- Compact design
- High speed
- High volumetric, mechanical and overall efficiency
- Available in ISO and UNI standard
|
| | | Features Fixed displacement axial piston pumps and motors swash plate design for open circuit applications.
The design is extremely compact and it can integrate many functions.
An electrically controlled valve can be fitted on the pump and an electronic board controls the flow and the speed of the powered motor.
Unidirectional pumps LFP48:
displacements from 1.65 in³/rev (27 cm³/rev) to 2.94 in³/rev (48,2 cm³/rev)
Reversible motors LFM30:
displacements from 1.34 in³/rev (22 cm³/rev) to 1.84 in³/rev (30,2 cm³/rev)
Max. peak pressure up to 5075 psi (350 bar) Pump - Possibility to have on the pressure line a three-position electrically controlled valve with relief valve
- Possibility to mount an auxiliary gear pump with common suction
- Internal drain
Motor - Reversible rotation with integral antishock valves
- European and SAE standard mounting flanges
- Side or rear inlet options
- Compact size
|
|
|
变量轴向柱塞泵 | Variable displacement axial piston pumps |
| | | | |  LVP | | Virtual 360° view | | Pdf in Reserved Area |
|
Features Variable displacement axial piston pumps swash plate design.
PLATA pumps are ideally suited for medium and high pressure open circuit applications
Displacements from 1.74 in³/rev (28,49 cm³/rev) to 5.37 in³/rev (87,9 cm³/rev)
Max. peak pressure up to 5075 psi (350 bar)
Max. speed up to 3000 min-1 - Energy savings
- Low noise emission
- Short response time
- Drive shaft bearing suitable for radial and axial loads
- Multiple combinations
| Controls - Pressure compensator
- Flow and pressure compensator (Load Sensing)
- Torque limiter
- Electrohydraulics servocontrols
|
| | | | | | MVP | | Pdf in Reserved Area | | Multimedia in Reserved Area |
|
Features Variable displacement axial piston pumps swash plate design ideally suited for open circuit in mobile hydraulic applications.
The compact design allows to be mounted directly on engine motors.
Displacements from 28,5 cm3/rev (1.74 in3/rev) to 84 cm3/rev ( 5.12 in3/rev).
Max. peak pressure up to 350 bar (5100 psi.)
Max. speed up to 3000 min-1 - Exceptional working life expectancy.
- Low noise emission.
- Drive shaft bearing suitable for radial and axial loads.
- Multiple combinations.
| Controls - Min. and max. displacement limiter.
- Pressure compensator.
- Flow and pressure compensator (Load-Sensing).
- Torque limiter.
|
| | | | | | DVP | | Pdf in Reserved Area |
| | SVP | | Pdf in Reserved Area |
|
Features Variable displacement axial piston pumps swash plate design for open circuit applications.
SVP single flow, DVP dual flow on piston pump and an additional piggybacked gear pump.
The automatic overall torque limiter allows to optimize the performance of the machine.
SVP and DVP pumps has been designed specifically for mini excavators where compactness and ease of installation are critical.
Piston pump: displacements from 0.48 in³/rev (7,8 cm³/rev) to 0.91 in³/rev (30 cm³/rev)
Gear pump: displacements from 0.30 in³/rev (4,95 cm³/rev) to 1.29 in³/rev (21,14 cm³/rev)
Max. speed up to 2600 min-1 - Compact design
- Torque limiter
- Energy savings
- Low noise emission
- Long service life
Different combinations are available. |
|
|
液压手动泵
过滤器
| | Ikron “Fluid Filtration” from Casappa “Fluid Power Design”
An accurate filtration expands the life of all components and improves the overall efficiency of your hydraulic system. - Suction filters
- Return filters
- In line filters spin-on type
- In line medium and high pressure filters
- Accessories
|
|
|
|
|
|
