| 型号 | Heinzinger electronic | 规格 | Heinzinger electronic |
| 品牌 | Heinzinger electronic | 材质 | Heinzinger electronic |
| 名称 | Heinzinger electronic | 适用范围 | Heinzinger electronic |
希而科贸易（上海）有限公司-德国Silkroad24 GmbH 中国办事处
联系人：张敏 （业务部销售经理）
TEL:13585754584 021-58375543-829
FAX:021-61179684
EMAIL:zm@
QQ:1784691511
MSN:zhangsir_goal@
希而科优势代理德国Heinzinger electronic GmbH电源 接口 界面 系统 附件
产品系列：
Interfaces
In addition to the analogue interface, which is a standard feature on almost all devices, various digital interfaces are available for all power units. Either for installation as a plug-in card or as an external interface adapter. Ask us about interface solutions that are not listed here.
Series overview
 Analogue Interfaces |  Digital Interfaces |  External digital interface |  Programable control unit |
Analogue interfaces
Analogue interface 0...10V, with and without potential separation
- Built into nearly all Heinzinger power units as a standard feature, allows for easy remote control of the devices
- Potential-separated version available as an option
- Nominal value specification for voltage and current
- Monitor signal for voltage and current
- External "stand-by" (depends on device)
- Further functions possible, depends on power unit type
- 10 V reference voltage available for external switching
- 15-pin. Sub-D-socket, counterplug included with delivery
Schnittstellenbelegung Standardgeräte (PDF)Digital interfaces
RS232, RS485, IEEE488 (GPIB), 12bit oder 16bit
- Available as plug-in card for many Heinzinger power units
- Combined interface RS232/RS485 (device option 72I/76I))
- Combined interface RS232/RS485 (device option 72I/76I))
- Resolution 12bit (option 72) or 16bit (option 76), also for devices with highest precision
- Makes it possible to set voltages & currents and read out the voltage & current values
- External "stand-by" (depends on device)
- Reading out the regulation status (depends on device)
- Further functions, depends on power unit type
- Special functions and customised signals possible
- Version with beam waveguide adapter (insulation by beam waveguide) available upon request
Datasheet (PDF)External digital interface
Eco-Bus, digital Interface RS232,IEEE488
- External interface adapter, makes possible the digital control of all power units with 0...10V analogue interface
- Available as combined RS232/IEEE488 interface (other versions available upon request)
- Voltage and current programming and reading
- Supports the standard functions of the analogue interface, additional functions possible depending on the device
- Makes retrofitting with digital control easily possible, also for older power units that feature an analogue interface
Datasheet (PDF)Programmable control unit
Programmable front panel control with digital interface
- Programming the power unit functions from the front panel
- Integrated RS232/IEEE488 digital interface
- Up to 32 programs can be saved
- Up to 16 program steps per program (linking of programs possible, max 511 program steps)
- Specification of the voltage and current values by the 10-digit keypad or "sweep" function
- Two-line display
- Device-specific special functions possible
Datasheet (PDF)Systems / OEM solutions
Based on our standard power units we offer systems and customised products in form of OEM solutions. These products are developed in close cooperation with our customers and are tuned to the respective application. Several examples can be found here.
Series overview
 HeinzingerEnergyRecovery |  System solutions high-voltage |  OEM solutions |  Electronic high-performance loads |  DC rectifier unit |  High-speed high-voltage switch |
High performance power supplies with integrated "Heinzinger Energy Recovery"
PTNer series (Energy Recovery), e.g. for hybrid test bed
- Robust power unit based on the PTN3p series with "Heinzinger Energy Recovery"
- Integrated energy recovery that converts energy returning from the consumer back into network voltage and is fed back into the supply network
- Very good dynamic behaviour
- Minimal threshold between power units and energy recovery mode with intelligent detection of the operating mode of the consumer
- Comprehensive digital and analogue control methods
- Power unit function with integrated option "Battery characteristic curves" for recreating the behaviour of a battery
- Suited for non-stop operation, extremely reliable
- Modular design
- Galvanic separation of the consumer in energy recovery mode
- Power unit available in water-cooled version
Go to Heinzinger Energy Recovery Site
System solutions high-voltage
HV system with raised low-voltage power unit
- High-voltage complete system, consisting of:
- 2 x HV power unit 20kV
- 2 x High-voltage resistor
- Low-voltage power units, insulated constructed and raised to high-voltage potential
- HV separation transformer - Insulated control elements
- External control by beam waveguide
- Various versions are possible based on our high- and low-voltage power units
- Completely assembled, e.g. in 19" cabinet
Electronic high-performance loads
TEL series
- Electronic precision DC load according to the principle of the current sink
- In connection with Heinzinger power unit as combination source/sink (energy recovery see PTNer)
- Different modes of regulation, customised, possible:
- Current regulated, load works as constant current sink (current is kept constant independent from the voltage)
- Voltage regulated, input voltage is kept constant by the variable load of the source, nominal voltage is specified. The load always adjust the current that ensures the exact regulation of the nominal voltage (sense mode possible)
- Resistance regulated, selectively with resistance-linear regulation or voltage-linear resistance regulation - Comprehensive digital and analogue control methods
- Also available in water-cooled version
DC rectifier unit
OEM solution power2DRIVE
- Rectifier unit for supplying DC drives (operating mode: partially controlled three-phase bridge)
- Regulated output voltage
- Adjustable chopper application threshold
- Brake chopper connection
- Undervoltage and overvoltage monitoring
- Extensive external control and evaluation possibilities
- Power components mounted on cooling/mounting plate made of copper, prepared for "coldplate" assembly
- Stainless steel housing with detachable control electronics for easer handling during installation
Datasheet (PDF)High-speed high-voltage switch & ARC detection
OEM solution "SparkDAC"
- High-speed high-voltage switch
- HV flashover detection by beam waveguide
- Detecting and signalling of HV flashovers in μ-sec range
- Switching off the voltage and shorting the consumer within few μ-sec
- Time delayed switching on again possible
- Extensive setting and evaluation possibilities
- For connecting Heinzinger high-voltage power units
- For many load types and various switching capacities or voltages
- Customer-specific versions, tuned to the applicationDatasheet (PDF)
Accessoires
In addition to precise power units you will also find high-voltage cables and HV plug connectors in our production program. The cable and high-voltage plugs are available from stock for voltages up to 100kV. We can provide for even greater voltages. We can gladly inform you on the possibilities.
For accessories for our power units we also offer various digital interfaces as plug-in cards or as external devices. Further options on the devices can be found in the respective device description in the data sheet.
High-voltage cable
HVC10, HVC30, HVC65, HVC100
- High-voltage cable for nominal DC voltage 10kV (HVC10), 30kV (HVC30), 65kV (HVC65), 100kV (HVC100) and 200kV (HVC200), for higher voltages upon request
- Screened lines, inner lines as wires
- Especially developed and tested for DC high-voltage applications (For AC applications upon request)
- Red cable sheath with signal effect
- Also available ready-made with pre-assembled HV plug
datasheet (PDF)High-voltage plug
HVS10, HVS35, HVS65, HVS100
- High-voltage plug for voltages up to 10kV (HVS10), 35kV (HVS35), 65kV (HVS65) and 100kV (HVS100). Higher voltages upon request
- Simple and secure cable attachment
- Tested for DC high voltage
- Designed for use of Heinzinger high-voltage cable
datasheet (PDF)High-voltage sockets
HVB10, HVB35, HVB65, HVB100
- High-voltage installation sockets for voltages up to 10kV (HVB10), 35kV (HVB35), 65kV (HVB65) and 100kV (HVB100). Higher voltages upon request
- For use with Heinzinger high-voltage plugs
- Tested for DC high voltage
- Voltage-stable with air-insulated or encapsulated assembly depending on model
datasheet (PDF)