当不知道淮安INA轴承是否能安装，又或者这个角接触球轴承的安装方法对与不对或与其他有什么区别？
When it is not known whether Huaian INA bearings can be installed, or whether the installation method of this angular contact ball bearings is different from other ones or not?
如果发生这种情况，首先检查安装方法是否错误。以下是角接触球轴承的标准安装程序：
If this happens, first check if the installation method is wrong. The following are the standard installation procedures for angular contact ball bearings:
1。轴承安装应在清洁无尘的室内进行。轴承应仔细选择和匹配。轴承隔板应磨平。在内外环隔板尽可能高的前提下，隔板的平行度应控制在1um以下。
1. Bearing installation should be carried out in a clean and dust-free room. Bearings should be carefully selected and matched. Bearing diaphragm should be ground flat. On the premise that the inner and outer ring diaphragms are as high as possible, the paralleli*** of the diaphragms should be controlled below 1um.
2。安装前应清洁轴承。清洗时内环向上倾斜，手灵活，无卡滞感。干燥后，应加入一定量的润滑脂。如果属于油雾润滑，应加少量油雾。
2. Bearings should be cleaned before installation. The inner ring inclines upward when cleaning, and the hand is flexible, without sticking feeling. After drying, a certain amount of grease should be added. If it belongs to oil mist lubrication, a ***all amount of oil mist should be added.
三。轴承安装应使用专用工具，用力均匀，不得敲击。
Three. Special tools should be used for bearing installation, with uniform force and no knocking.
4。淮安INA轴承存放应清洁通风，无腐蚀性气体，相对湿度不超过65个百分点，长期存放应定期防锈。
4. Huaian INA bearings should be kept clean, ventilated, non-corrosive gas, relative humidity not exceeding 65 percentage points, long-term storage should be regularly rust-proof.
为了固定轴承外圈，固定轴承外圈***有.效的方法是什么？
In order to fix the outer ring of the bearing, the *** of the outer ring of the fixed bearing is effective. What is the effective method?
问题描述：
Problem Description:
固定轴承外圈***有.效的方法是什么？
Fixed bearing outer ring *** has. What is the effective method?
轴承外圈安装在轴承箱内。轴承箱的一端通常由轴承箱上的台肩固定，另一端由端盖、螺纹环和带弹性挡圈的孔固定。轴承箱和轴承环上的轴肩与轴向紧固件的接触尺寸可根据轴承尺寸表中列出的各种淮安INA轴承的安装尺寸确定。
The outer ring of the bearing is installed in the bearing box. One end of the bearing box is usually fixed by the shoulder on the bearing box, and the other end is fixed by the end cap, thread ring and hole with elastic retaining ring. The contact dimensi*** between the shoulder and the axial fastener on the bearing box and ring can be determined according to the installation dimensi*** of various Huaian INA bearings listed in the bearing dimension table.
（1）端盖紧固
(1) End cap fastening
对于各种向心轴承和推力轴承，轴承具有较高的转速和较大的轴向载荷。端盖通过螺钉拧紧轴承外圈，端盖也可以通过弯曲路径密封。
For various centripetal and thrust bearings, bearings h***e higher rotational speed and larger axial load. The end cap tightens the outer ring of the bearing by screw, and the end cap can also be sealed by bending path.
（2）扣环
(2) ***les
适用于转速高、轴向负荷大的淮安INA轴承，不适合拧紧端盖。当用螺纹环紧固向心推力轴承时，可以调整轴承的轴向间隙。
It is suitable for Huaian INA bearing with high rotating speed and large axial load. It is not suitable for tightening end cap. When the threaded ring is used to fasten the centripetal thrust bearing, the axial clearance of the bearing can be adjusted.
（3）孔用弹性挡圈
(3) Elastic retaining rings for holes
该紧固方法轴向位置小，安装拆卸方便，制造简单。用于承受较小的轴向载荷。在轴承和弹簧之间增加调整环，以便于调整轴向位置。
The fastening method has the advantages of ***all axial position, convenient installation and disassembly, and simple manufacture. Used to withstand ***aller axial loads. An adjusting ring is added between the bearing and the spring to facilitate the adjustment of the axial position.
（4）止动环的紧固
(4) Fastening of stop ring
轴承外圈带有止动槽的单列深沟球轴承由止动环紧固。当轴承箱中的止动边缘由于条件限.制或需要减小部件轮廓尺寸而无法处理时，选择这种类型的铀轴承。
Single row deep groove ball bearings with stop grooves in the outer ring of bearings are fastened by stop rings. This type of uranium bearing is selected when the stop edge in the bearing box is unable to be processed due to the limitation of conditi***, or the need to reduce the contour size of the components.
文章来自：淮安SKF轴承 www.wh-
文章来自：淮安INA轴承 a-
文章来自：淮安NSK轴承
***：524085168
电话：0510-81207777
手机：13311666672/13395185757