对于各种进口淮安SKF轴承，不能充分利用，延长使用寿命。这需要在日常使用过程中注意许多细节，以避免因使用不当而造成的损失。轴承也不例外。当轴承间隙过小时，***常见的情况是轴承发热，如果转速较快，可能会出现蓝色烧损现象。
For all kinds of imported Huaian SKF bearings, they can not be fully utilized to prolong service life. This requires attention to many details in the daily use process to ***oid the loss caused by improper use. Bearings are no exception. When the bearing clearance is too ***all, ***'s common condition is that the bearing is heated. If the speed is fast, the phenomenon of blue burning may occur.
当轴承温度升高时，应首先判断是否误操作。如果确实增加了，则应解决以下问题：
When the bearing temperature rises, the misoperation should be judged first. If it does increase, the following issues should be addressed:
检查油标的油位是否正常，如异常，检查油箱排放阀是否关闭。如果是关闭的，应该修理。如果垫片渗油，应停止处理。取油样观察油的颜色是否发生变化，并进行老化试验。如果确认淮安SKF轴承变质，应在停机后更换.新油。
Check whether the oil level of the oil mark is normal, if abnormal, check whether the tank discharge valve is closed. If it is closed, it should be repaired. If the gasket seeps oil, the treatment should be stopped. Oil samples were taken to observe whether the color of oil changed, and the aging test was carried out. If the deterioration of Huaian SKF bearing is confirmed, the new oil should be replaced after shutdown.
检查轴承是否有异常噪音，检查轴承摆动是否异常。应检查调速器的油压。如果油压低，可能导致冷凝水液压阀关闭。应检查冷凝水压力、水流和管道系统。如果水压低，过滤器可能堵塞，不能及时处理，可以停止处理。确认能正常工作后，再投入使用。
Check whether the bearing has abnormal noise, check whether the bearing swing is abnormal. The oil pressure of the governor should be checked. If the oil pressure is low, it may cause the condensate hydraulic valve to close. Condensate pressure, water flow and pipeline system should be checked. If the water pressure is low, the filter may be blocked and can not be handled in time, the treatment can be stopped. After confirming that it can work properly, it will be put into use again.
可能是轴承油质量恶化、油本身不干净或运行中的油变质，如油中含水量增加、油酸增加、油润滑效果降低、轴瓦腐蚀、淮安SKF轴承温度升高或中断等。轴承冷凝水开启。
It may be the deterioration of bearing oil quality, the unclean oil itself or the deterioration of oil in operation, such as the increase of water content in oil, the increase of oleic acid, the decrease of oil lubrication effect, the corrosion of bearing bush, the rise or interruption of SKF bearing temperature in Huaian, etc. The bearing condensate water opens.
轴承温升故障信号发出。黑色和黄颜色指针与温度计盘（膨胀温度计）上的黄颜色指针重合或超出。侧板水轮机机械故障指示灯字板亮，指示轴承仪表温升，信号继电器动作。
The bearing temperature rise fault signal is sent out. The black and yellow color pointers coincide with or exceed the yellow color pointers on the thermometer disk (expansion thermometer). Side plate hydraulic turbine mechanical failure indicator light word board bright, indicating bearing instrument temperature rise, signal relay action.
热传感器可以随时监测角接触球轴承的工作温度。当温度超过规定值时，自动警报或停机，防止轴烧坏事故发生。轴承的温度可以从轴承外部的温度获得。如果油孔能直接测量进口淮安SKF轴承外圈的温度，则更为合适。
Thermal sensor can monitor the working temperature of angular contact ball bearing at any time. When the temperature exceeds the prescribed value, automatic alarm or shutdown can prevent shaft burnout accident. The temperature of the bearing can be obtained from the temperature outside the bearing. If the oil hole can directly measure the temperature of the outer ring of the imported Huaian SKF bearing, it is more suitable.
通常工作温度在150度以上的角接触球轴承称为高温轴承。当含铬钢温度超过150度时，其硬度急剧下降，尺寸不稳定，使轴承无办法使之正常工作。按上述要求回火的轴承钢，可在工作温度下正常使用。然而，轴承的使用寿命随着回火后硬度的降低而降低。
Usually angular contact ball bearings with working temperature above 150 degrees are called high temperature bearings. When the temperature of chromium-containing steel exceeds 150 degrees, its hardness drops sharply and its size is unstable, which makes it impossible for bearings to work properly. Bearing steel tempered according to the above requirements can be used normally at working temperature. However, the service life of bearings decreases with the decrease of hardness after tempering.
文章来自：淮安SKF轴承 www.wh-
Article from: Huaian SKF Bearing www.wh-
文章来自：淮安INA轴承 a-
Article from: Huaian INA Bearing a-
文章来自：淮安NSK轴承
Article from: Huaian NSK Bearing
***：524085168
电话：0510-81207777
手机：13311666672/13395185757