轴承清洗过程也会损坏轴承，这不会欺骗你，因为清洗时淮安NSK轴承会有轻微擦伤，所以轴承的拆卸应首先记录润滑油的用量和外观的一些注意事项，如下：轴承清洗过程：
Bearing cleaning process will also damage the bearings, which will not deceive you, because Huaian NSK bearings will be slightly scratched when cleaning, so the removal of bearings should first record the amount of lubricant and some external c***iderati***, as follows: bearing cleaning process:
轴承清洗可分为粗加工和清洗。金属格栅可以放置在使用中的容器底部。
Bearing cleaning can be divided into rough processing and cleaning. The metal grille can be placed at the bottom of the container in use.
粗加工时，用刷子清chu油中的油脂或粘合剂。如果轴承在油中转动，滚动面会受到***的损坏。清洁时，轴承应在油中缓慢小心地转动。
When roughing, use a brush to clear grease or adhesives in Chu oil. If the bearing rotates in oil, the rolling surface will be damaged by foreign bodies. When cleaning, bearings should rotate slowly and carefully in oil.
轴承清洗注意事项：
Notes for bearing cleaning:
1。使用的清洁剂是中性非水柴油或煤油。必要时也可以使用温度碱液。无论使用哪种清洁剂，都应定期过滤以保持清洁。
1. The detergent used is neutral non-aqueous diesel or kerosene. Temperature lye can also be used when necessary. No matter which cleaner is used, it should be filtered regularly to keep it clean.
2。清洁后，轴承立即涂上防锈油或润滑脂。
2. After cleaning, the bearing is immediately coated with rust-proof oil or grease.
3。为了确定拆下的淮安NSK轴承是否可以重复使用，bi须检查轴承的尺寸精度、旋转精度、内部间隙和配合面、滚道表面、保持架和密封圈。判断标准根据机械性能、重要性和检查周期而变化。如果发生以下损坏，不得重复使用轴承，bi须更换。
3. In order to determine whether the di***antled Huaian NSK bearings can be reused, Bi must check the dimension accuracy, rotation accuracy, internal clearance and mating surface, raceway surface, cage and sealing ring of the bearings. Judgment criteria vary according to mechanical performance, importance and inspection cycle. If the following damage occurs, the bearing shall not be reused and the Bi shall be replaced.
（1）轴承安装前，应根据设计图纸的技术要求，用合适的量具检查轴、座孔及相关零件的加工质量（如尺寸精度、形状精度、表面粗糙度）。
(1) Before installation of bearings, the processing quality of shafts, seat holes and related parts (such as dimension accuracy, shape accuracy and surface roughness) should be checked with appropriate measuring tools according to the technical requirements of the design drawings.
（2）如果轴和轴承座孔的装配面上有碰伤、毛边、锈斑或固体颗粒（如碎片、沙子、粘土等），不仅会使轴承安装困难，还会使安装位置不正确。当固体颗粒落入B中时，它们起到研磨剂的作用。轴承座孔。轴承。当淮安NSK轴承转动时，会磨损或刮伤轴承的工作表面。安装前bi须小心。如果在检查中发现这些que陷，应予以纠正。例如，用油锉去除毛边、鼓包和锈斑，用细砂布打磨，如清理固体颗粒、污垢等。
(2) If there are bruises, rough edges, rust spots or solid particles (such as debris, sand, clay, etc.) on the assembly surface of the shaft and bearing seat holes, it will not only make the installation of bearings difficult, but also make the installation position incorrect. When solid particles fall into B, they act as abrasives. Bearing seat hole. Bearing. When Huaian NSK bearings rotate, they will wear or scratch the working surface of bearings. Be careful before installing bi. If these que traps are found in the inspection, they should be corrected. For example, oil files are used to remove rough edges, bulges and rust spots, and fine sand cloth is used to polish, such as cleaning solid particles, dirt and so on.
（3）装配面应用清洁的***、煤油、***或二***溶液清洗，用干净的布擦拭，然后涂上薄薄的润滑剂，便于安装和操作。
(3) The assembly surface should be cleaned with clean gasoline, kerosene, toluene or xylene solution, wiped with clean cloth, and then coated with thin lubricant for easy installation and operation.
（4）安装前，打开轴承箱，将轴承箱浸入上述***和其余液体中，用手轻轻转动，确保轴承箱、滚动件和滚道表面的密封油彻底清洗干净。
(4) Before installation, open the bearing box, immerse the bearing box in the above-mentioned gasoline and other liquids, and rotate it gently by hand to ensure that the sealing oil on the bearing box, rolling parts and raceway surface is thoroughly cleaned.
（5）清洗大量轴承时，应将包装好的油用90-100摄氏度的热油熔化。同时，所有使用过的油应使用无缝工具和无废料工具清洗，然后熨烫几分钟，然后用煤油清洗，***后用***清洗。清洁后，戴上薄膜手套，用干净的布或纸擦干工作台上的轴承。
(5) When cleaning a large number of bearings, the packaged oil should be melted with hot oil of 90-100 degrees Celsius. At the same time, all used oils should be cleaned with seamless tools and waste-free tools, then ironed for a few minutes, then cleaned with kerosene, and then cleaned with gasoline after ***. After cleaning, wear film gloves and dry the bearings on the worktable with clean cloth or paper.
（6）注意带密封的淮安NSK轴承不能用这种方法清洗，密封内部应保持原样。
(6) Note that Huaian NSK bearing with seal can not be cleaned by this method, and the inside of seal should be kept as it is.
文章来自：淮安SKF轴承 www.wh-
Article from: Huaian SKF Bearing www.wh-
文章来自：淮安INA轴承 a-
Article from: Huaian INA Bearing a-
文章来自：淮安NSK轴承
Article from: Huaian NSK Bearing
***：524085168
电话：0510-81207777
手机：13311666672/13395185757