TESEQ MD 300 浪涌脉冲电流探头

TESEQ MD 300 浪涌脉冲电流探头特别为浪涌电流脉冲测量而设计测试探头与被测电路物理上隔离方便使用不需要额外的衰减器浪涌脉冲电流探头 规格参数：***大峰值电流： 5000 Amp***大RMS电流： >63 Amp额定率：500:1 (into 1 MΩ system)              1000:1 (into 50 Ω system)敏感度：0.002 V/Amp (1 MΩ system)              0.001 V/Amp (50 Ω system)低频(3 dB cut off)： <10 Hz高频(3 dB cut off)： >20 MHz孔直径：8 mm探头接头：***A同轴线缆: ***A 和 BNC 接头操作温度： 0 ～ 55°C输出阻抗：50 Ω***度： <&plu***n;2%Surge Pulse Current Probe Set MD 300 . Special designed for surge current pulse measurements . Probe is physically isolated from the circuit . Ready to use . No additional attenuators needed  The MD 300 probe has been specially designed to verify surge current pulses as specified in IEC 61000-4-5, ANSI C62.41 and their derivates. The main advantage of the MD 300 current probe is, that the measuring system is physically isolated from the circuit under test. The MD 300 current probe is ready to use as coming along with pre-mounted coaxial cable. The BNC-end plug needs to be connected to the high-impedance input or 50 Ω input of an ordinary momory oscilloscope. Then the conductor carrying the surge current to be measured is passed through the hole in the current probe. The resulting voltage w***e shape on the oscilloscope will then be an authentical reproduction of the actual current w***e shape within the given accuracy. The probe can be used for current pulse verification on surge generators. Optional FISCHER or LEMO connectors are ***ailble for matching the safety banana connectors of the shorting cable to the HV output of the generator. For monitoring the EUT current during a test, an additional IEC adaptor with the safety banana connectors can be connected to the generator EUT output for observation of one lead at a time. Ordering information MD 300 set: Carry case, Current probe, Coax cable with ***A/BNC connector, Shorting cable with safety banana connectors, Calibration certificate, Manual Opti***: INA 6560 FISCHER to banana plug adaptor set INA 2042 LEMO to banana plug adaptor set INA 6554 IEC320 single phase to safety banana adaptor leads 2x 155-131 6mm to 4mm adaptors with safety banana connectors Note: The carry case povides space for all opti***. Specificati*** Maximum peak current 5000 Amp Maximum RMS current >63 Amp Nominal ratio 500:1 (into 1 MΩ system)  1000:1(into 50 Ω system) Sensitivity 0.002 V/Amp (1 MΩ system)  0.001 V/Amp (50 Ω system) Lower frequency (3 dB cut off) <10Hz Higher frequency (3 dB cut off) >20MHz Hole diameter 8mm Probe connector ***A Scope coax cable with ***A and BNC connectors Operating temperature 0 to 55°C Output impedance 50Ω Accuracy < &plu***n;2%  Agilent HP 70950A光谱分析仪Agilent HP 70950B光谱分析仪Agilent HP 70951A光谱分析仪Agilent HP 70952B光谱分析仪Zygo 7701C/ELaser Head 6mmAgilent HP 8147光时域反射仪Agilent HP 81521A光探头Agilent HP 81521B光探头Agilent HP 81522A光传感头Agilent HP 81524A光探头 Agilent HP 81525A光探头Agilent HP 8152A光功率计Agilent HP 81531A光功率计传感插件Agilent HP 81532A传感器Agilent HP 81