微尔技术支持-雪弗板振动刀切割机-阿克苏地区振动刀切割机

济南微尔振动刀切割优势：1.

切割一套汽车大包围脚垫，只需3-4分鐘

2：无需刀模、模切机，可节省大量的人力、刀模及模切机成本。

3：汽车内饰切割机，完全代替汽车座椅/座垫/脚垫/方向盘皮套、布套、海绵套的手工设计、打样和切割工序，助您节省大量人力、刀模及材料损耗成本。

4：可切割皮、海绵 覆布 皮革复合皮料、PVC脚垫、丝圈脚垫、纸张、纸板、PVC塑胶板、密封垫圈等柔性材料。

5.可切割KT板，皮革，布料，纤维，软金属，软塑料，环保新材料等，微尔震动刀切割设备，正越来越适用于新型行业，为智能化设备做出自己的贡献

Jinan Weier vibration cutter cutting advantages:

1.Cut a set of automobile big surround footpads， only 3-4 minutes.

2: There is no need for die and die-cutting machine， which can s***e a lot of manpower， cost of die and die-cutting machine.

3: The automobile interior trim cutting machine completely replaces the manual design， proofing and cutting processes of automobile seat/seat cushion/foot cushion/steering wheel cover， cloth cover and sponge cover， which helps you s***e a lot of manpower， cutting die and material loss costs.

济南微尔激光设备有限公司提示：振动刀切割机如果估计要设的刀深比之前的刀深很接近或者更深，可以按厂家技术指导的按钮把Z轴一次性移动到之前的刀深位置，注意，换成其他刀的时候，按这个按钮的时候需考虑清楚再按，否则可能会刺穿台面， 断刀。

Jinan Weier Laser Equipment Co.， Ltd. Tips: If the estimated cutter depth is close to or deeper than the previous cutter depth， you can move Z axis to the previous cutter depth at one time according to the button specified by the manufacturer"s technology. Note that when changing the growth knife， you need to c***ider clearly pressing this button again， otherwise you may pierce the table and break the knife.

济南微尔激光设备有限公司振动刀刀具调节问题解答

调刀和压轮的偏移量1， 先把SP2的类型设置成[压轮]， 并且调好深度，2， 先按切换到[压轮]。3， 然后按 【测试偏移】 按钮测试，测试的时候是用震动刀割一个十字，然后用压轮压另一个十字，如果这两个十字重合了，雪弗板振动刀切割机，就说明偏移量调好了。4，阿克苏地区振动刀切割机， 如果没有重合，那么通过点动按钮， 把压轮的中心移到震动刀割的那个十字的中心就可以了，皮革鞋振动刀切割机，***后按按钮保存，然后再按【测试偏移】按钮重新测试看下两个十字是否有完全重合。

如有更多问题详解请致电咨询，感谢您的观看。

Solution to Tool Adjustment Problem of Vibrating Knife in Jinan Weier Laser Equipment Co.， Ltd.

The offset of tool adjustment and press wheel is 1. First， the type of SP 2 is set to press wheel， and the depth is adjusted. Second，旋转刀振动刀切割机， press switch to press wheel. 3. Then press the [Test Offset] button to test. The test is done by cutting one cross with a vibrating knife and pressing another cross with a press wheel. If the two crosses coincide， the offset is adjusted. 4. If there is no coincidence， then move the center of the wheel to the center of the cross cut by the vibrating knife by clicking the button. Finally， press the button to s***e， and then press the [test offset] button to re-test whether the two crosses are completely coincident.

If you h***e more questi***， please call for c***ultation. Thank you for watching.