SKF轴承润滑脂LGMT2/1使其寿命更加漫长

空气中的油和氧之间的化学反应产生酸性物质。首先，它消耗SKF轴承润滑脂中的抗养化剂添加剂。但是，所产生的you机酸会在一定程度上腐蚀金属成分，***油的结构，降低其滴点，增加基础油的粘度，降低其流动性。大量实验表明，温度越高，润滑脂的寿命越明显。如果温度在90度到100度之间，每升高19度，脂质的寿命将缩短一半；如果温度在10度到150度之间，每升高15度，脂质的寿命将缩短一半。
The chemical reaction between oil and oxygen in the air produces acidic substances. First, it c***umes anti-nutrient additives in SKF bearing grease. However, the resulting youorganic acid will corrode the metal composition to a certain extent, destroy the structure of the oil, reduce its dropping point, increase the viscosity of the base oil, and reduce its fluidity. A large number of experiments show that the higher the temperature, the more ***ious the life of grease. If the temperature is between 90 and 100 degrees, the life span of lipids will be reduced by half for every 19 degrees increase; if the temperature is between 10 and 150 degrees, the life span of lipids will be reduced by half for every 15 degrees increase.
SKF轴承润滑脂在使用过程中被机械剪切力和离心力分离，降低了含油量、锥入度和硬化。经过一定程度后，润滑脂会完全失效。在机械剪切作用下，油脂结构会被***（如皂纤维的分离或取向），导致油脂软花，稠度降低，油脂减少。增加的油沉淀***终会导致故障。
SKF bearing grease is separated by mechanical shear force and centrifugal force during use, which reduces oil content, taper penetration and hardening. After a certain degree, the grease will completely fail. Under mechanical shearing, the structure of oil will be destroyed (such as the separation or orientation of soap fibers), resulting in the softening of oil, the decrease of c***istency and the decrease of oil. Increased oil precipitation *** will eventually lead to failure.
此外，使用润滑脂的环境中的水分、灰尘和***气体也是导致润滑脂变质的重要因素。例如，可以通过在润滑脂中添加铜、铁、铅和青铜等磨损颗粒来催化润滑脂的氧化。简而言之，润滑脂失效的原因有很多。有时它可能是由一个原因引起的，但更多的时候SKF轴承润滑脂是由许多因素引起的，或者是突破的原因，然后是其余原因共同作用的结果。
In addition, moisture, dust and harmful gases in the environment where grease is used are also important factors leading to grease deterioration. For example, the oxidation of grease can be catalyzed by adding wear particles such as copper, iron, lead and bronze into grease. In short, there are many reas*** for grease failure. Sometimes it may be caused by one reason, but more often SKF bearing grease is caused by many factors, or the cause of breakthrough, and then the result of the combined action of other reas***.
游离碱是指皂基润滑脂在制造过程中不与脂肪酸相互作用的过量碱；游离you机酸是指在制造过程中不可皂化的脂肪酸，或烃基润滑脂本身含有酸（环烷酸），或润滑脂中矿物油的氧化或皂化产物。
Free base refers to excessive base which does not interact with fatty acids in the manufacturing process of soap-based grease; free youorganic acid refers to unsaponifiable fatty acids in the manufacturing process, or hydrocarbon grease itself contains acid (naphthenic acid), or oxidation or saponification products of mineral oil in grease.
虽然可以安装各种轴承密封，但由于润滑脂技术不正确和使用不当，轴承早期失效率仍为36个百分点。任何SKF轴承润滑脂不当的轴承在其正常使用寿命内都将不可避免地发生故障。机械和设备轴承通常是***困难的部分，没有固定的润滑将是一个问题。在没有人工维护的情况下，是不可能实现的，可以开发自动润滑系统来达到***佳的润滑效果。对润滑脂、工具和you效润滑技术的需求将大大减少停机时间。
Although various bearing seals can be installed, the early failure rate of bearings is still 36 percentage points due to incorrect lubricating grease technology and improper use. Any bearing with improper SKF bearing grease will inevitably fail during its normal service life. Bearings of machinery and equipment are usually the difficult part of ***, and no fixed lubrication will be a problem. In the absence of manual maintenance, it is impossible to achieve, can develop automatic lubrication system to achieve *** good lubrication effect. Demand for grease, tools and you-effect lubrication technology will greatly reduce downtime.
密封件与其相对运动部件之间没有间隙。由于密封件与接头直接接触，接触面摩擦大，发热量高，润滑不顺畅，摩擦损坏，密封效果和性能降低。因此，只能在中低速条件下使用。接触式密封通常用于毡封、杯形密封和其余结构形式，并在不同的情况下使用。SKF轴承润滑脂是支撑其本质的部件。它的重要功能是引导轴的旋转。它也可以是轴承轴的空转部分。
There is no gap between the seal and its relative moving parts. Because of the direct contact between the seals and the joints, the contact surface has high friction, high calorific value, poor lubrication, friction damage, and the sealing effect and performance are reduced. Therefore, it can only be used in low and medium speed conditi***. Contact seals are usually used for felt seals, cup seals and other structural forms, and are used in different situati***. SKF bearing grease is the essential part to support it. Its important function is to guide the rotation of the axis. It can also be the idle part of the bearing shaft.
文章来自：SKF轴承润滑脂 www.wh-
Article from: SKF bearing grease www.wh-
文章来自：INA轴承 a-
Articles from: INA Bearing a-
文章来自：NSK轴承
Article from: NSK Bearing
***：524085168
***: 524085168
电话：0510-81207777
Tel: 0510-81207777
手机：13311666672/13395185757
Mobile phone: 13311666672/13395185757