现货A5052P-O铝板料 进口JIS标准

现货A5052P-O铝板料 进口JIS标准

Aluminum 5052-H34

Subcategory: 5000 Series Aluminum Alloy; Aluminum Alloy; Metal; Nonferrous Metal

Close Analogs:

Composition Notes: 
Aluminum content reported is calculated as remainder.
Composition information provided by the Aluminum Association and is not for design.

Key Wo***: UNS A95052; ISO AlMg2.5; Aluminium 5052-H34; AA5052-H34

Component    Wt. % Al 95.7 - 97.7   Cr 0.15 - 0.35   Cu Max 0.1   Fe Max 0.4

Component    Wt. % Mg 2.2 - 2.8   Mn Max 0.1   Other, each Max 0.05

Component    Wt. % Other, total Max 0.15   Si Max 0.25   Zn Max 0.1

Material Notes: 
Data points with the AA note h***e been provided by the Aluminum Association, Inc. and are NOT FOR DESIGN.

Physical Properties	Metric	English	Comments
Density	2.68 g/cc	0.0968 lb/in�	AA; Typical
Mechanical Properties
Hardness, Brinell	68	68	AA; Typical; 500 g load; 10 mm ball
Hardness, Knoop	91	91	Converted from Brinell Hardness Value
Hardness, Vickers	78	78	Converted from Brinell Hardness Value
Ultimate Tensile Strength	262 MPa	38000 psi	AA; Typical
Tensile Yield Strength	214 MPa	31000 psi	AA; Typical
Elongation at Break	10 %	10 %	AA; Typical; 1/16 in. (1.6 mm) Thickness
Elongation at Break	14 %	14 %	AA; Typical; 1/2 in. (12.7 mm) Diameter
Modulus of Elasticity	70.3 GPa	10200 ksi	AA; Typical; ***erage of tension and compression. Compression modulus is about 2% greater than tensile modulus.
Ultimate Bearing Strength	469 MPa	68000 psi	Edge distance/pin diameter = 2.0
Bearing Yield Strength	303 MPa	43900 psi	Edge distance/pin diameter = 2.0
Poisson's Ratio	0.33	0.33
Fatigue Strength	124 MPa	18000 psi	AA; 500,000,000 cycles completely reversed stress; RR Moore machine/specimen
Machinability	50 %	50 %	0-100 Scale of Aluminum Alloys
Shear Modulus	25.9 GPa	3760 ksi
Shear Strength	145 MPa	21000 psi	AA; Typical
Electrical Properties
Electrical Resistivity	4.99e-006 ohm-cm	4.99e-006 ohm-cm	AA; Typical at 68癋
Thermal Properties
CTE, linear 68癋	23.8 祄/m-癈	13.2 礽n/in-癋	AA; Typical; ***erage over 68-212癋 range.
CTE, linear 250癈	25.7 祄/m-癈	14.3 礽n/in-癋	***erage over the range 20-300篊
Specific Heat Capacity	0.88 J/g-癈	0.21 BTU/lb-癋	Estimated from trends in similar Al alloys.
Thermal Conductivity	138 W/m-K	960 BTU-in/hr-ft�-癋	AA; Typical at 77癋
Melting Point	607 - 649 癈	1125 - 1200 癋	AA; Typical range based on typical composition for wrought products 1/4 inch thickness or greater
Solidus	607 癈	1125 癋	AA; Typical
Liquidus	649 癈	1200 癋	AA; Typical
Processing Properties
Annealing Temperature	343 癈	650 癋	holding at temperature not required
Hot-Working Temperature	260 - 510 癈	500 - 950 癋