扬州INA轴承润滑油的一般要求
General requirements for Yangzhou INA bearing lube oil
（1）减少摩擦磨损，降低摩擦阻力，节约能源，减少磨损，延长扬州INA轴承的使用寿命，提高经济效益。
(1) Reduce friction and wear, reduce friction resistance, s***e energy, reduce wear and tear, prolong the service life of Yangzhou INA bearing, improve economic benefits.
（2）需要冷却，以随时从机器上去除摩擦热。
(2) cooling is needed to remove frictional heat from the machine at any time.
（3）需要密封、防漏和防尘，以防止气体窜流。
(3) seal, leak proof and dust-proof are required to prevent gas channeling.
（4）腐蚀与防锈。有必要保护扬州INA轴承摩擦表面免受腐蚀或外部腐蚀。
(4) corrosion and rust prevention. It is necessary to protect the friction surface of INA bearing in Yangzhou from corrosion or external corrosion.
（5）清洗、清洗、清洗和去除摩擦面积。
(5) cleaning, cleaning, cleaning and removing the friction area.
（6）应力分散缓冲器、分散载荷、减震和减震。
(6) stress dispersion buffer, dispersed load, shock absorption and shock absorption.
（7）动能传递、液压系统、遥控马达和摩擦无级变速器。
(7) kinetic energy transfer, hydraulic system, remote control motor and friction CVT.
（a）油浴润滑
(a) oil bath lubrication
扬州INA轴承油浴润滑是***常用的润滑方法之一，适用于中低速轴承。使用该方法时，应注意控制油量，油面高度应略低于下轴承滚动轴承的中心线。过多的油会引起过高的温度扰动，而油的缺乏会导致轴承早期失效。
Yangzhou INA bearing oil bath lubrication is one of the most commonly used lubrication methods, suitable for middle and low speed bearings. When using this method, attention should be paid to controlling the oil volume, and the oil surface height should be slightly lower than the centerline of the rolling bearing of the lower bearing. Too much oil will cause excessive temperature disturbance, and the lack of oil will lead to early failure of bearings.
（b）喷油润滑
(b) oil spray lubrication
当扬州INA轴承在低速和中等负荷下高速运转时，滚子和保持架的转动使空气以相当大的速度围绕轴承旋转。为了保证向高速轴承提供足够数量的润滑油，润滑油必须从轴承的一端喷洒到轴承并润滑轴承，然后油从另一端重新流入油箱。润滑油的喷射速度不应低于15米/秒，油将直接注入轴承。
When Yangzhou INA bearings operate at high speeds at low and medium speeds, the rotation of rollers and cages causes air to rotate around the bearings at c***iderable speeds. To ensure that a sufficient quantity of lubricating oil is provided to the high speed bearing, the lubricating oil must be sprayed from one end of the bearing to the bearing and lubricate the bearing, and then the oil is re flowing into the tank from the other end. The injection speed of the lubricating oil should not be less than 15 m / sec, and the oil will be injected directly into the bearing.
（c）油滴润滑
(c) oil drop lubrication
扬州INA轴承润滑油是通过将润滑油的重量逐个减少到摩擦副来润滑的。这种润滑方法适用于少量容易接近的摩擦副。当轴承部件需要润滑油时，润滑油滴可以被润滑。滴油量通常为每滴3 s～8 s，过多的油会增加轴承的温升。
The lubricating oil of INA bearing in Yangzhou is lubricated by reducing the weight of lubricating oil one by one to the friction pair. This lubrication method is applicable to a ***all number of easily accessible friction pairs. Lubricating oil droplets can be lubricated when the bearing parts need lubricating oil. The amount of dripping oil is usually 3 s to 8 s per drop, and excessive oil will increase the temperature rise of the bearing.
（d）循环油润滑
(d) circulating oil lubrication
当扬州INA轴承转速较高时，轴承温升相应增加，导致油的老化。循环油润滑能有效地防止上述现象的发生。润滑油通过油泵送到轴承部，在轴承的另一端设置有油出口。轴承润滑油经过滤冷却后可循环使用。该方法适用于高速轴承零件。但是注意，油出口应该大于油入口，这样就不会在轴承座中留下剩余的油。
When the INA bearing speed of Yangzhou is higher, the temperature rise of the bearing increases correspondingly, resulting in the aging of oil. Circulating oil lubrication can effectively prevent the above phenomena. The lubricating oil is sent to the bearing part through an oil pump, and an oil outlet is arranged at the other end of the bearing. Bearing lubricating oil can be recycled after filtration and cooling. This method is suitable for high speed bearing parts. But notice that the oil outlet should be larger than the oil inlet so that no remaining oil will be left in the bearing block.
（e）油气润滑
(E) oil and gas lubrication
当扬州INA轴承在高速、高温和重载下工作时，通过压缩空气与少量润滑油混合，将油雾注入到运行轴承中。与其它润滑方法相比，该方法能使工作温度降到***低，使轴承转速达到***高。高压气流不仅可以用来冷却轴承，而且可以有效地防止杂质***。
When Yangzhou INA bearing works at high speed, high temperature and he***y load, oil mist is injected into the running bearing by mixing compressed air with a ***all amount of lubricating oil. Compared with other lubrication methods, this method can minimize the working temperature and make the bearing speed reach the highest. High pressure airflow not only can be used to cool the bearing, but also effectively prevent impurities from invading.
文章来自：扬州SKF轴承 www.wh-
The article comes from: Yangzhou SKF bearing www.wh-
文章来自：扬州INA轴承 a-
The article comes from: Yangzhou INA bearing a-
文章来自：扬州NSK轴承
The article comes from: Yangzhou NSK bearing
***：524085168
电话：0510-81207777
手机：13311666672