NABZ Automatic Variable Ratio Group Tester 南澳电气NABZ全自动变比组别测试仪
产品简介
南澳电气NABZ全自动变比组别测试仪的变比，操作过程繁琐、测量范围狭窄，已经不适应现代测量快节奏、***率的要求。为此，南澳电气（武汉）有限公司采用现代电子技术，研制出了新一代全自动变比组别测试仪。它体积小，重量轻，精度高，稳定性好。南澳电气NABZ全自动变比组别测试仪采用了大屏幕中英文液晶屏显示、内置中英文菜单式操作，完成一组变压器的测试只需11秒。NABZ全自动变比组别测试仪是电力工业部门的理想测试仪器。
南澳电气NABZ全自动变比组别测试仪产品别名
变压器变比组别测试仪，变压器双臂电桥
南澳电气NABZ全自动变比组别测试仪产品特性
1．自动测量接线组别。
2．自动进行组别变换。
3．自动切换相序。
4．自动切换量程。
5．自动校表。
6．输入标准变比后，能自动计算出相对误差。
7. 一次测量完成，自动切断试验电压 。
8. 设置数据,测量结果自动保存，可查看以前数据。
9. 测量有载变压器,只输入一次变比。
南澳电气NABZ全自动变比组别测试仪产品参数
1．变比测量范围： 1—10000
2．组别：1—12点
3．精度: 1-1000 0.2 级 1000-10000 0.5级
4．电源：AC220V &plu***n;10%，50HZ
5．使用环境温度：-5℃ ─ 40℃
6．使用环境湿度：＜85%
7．体积：430mm×320mm×215mm
8．重量：8Kg
南澳电气NABZ全自动变比组别测试仪注意事项
1. ***1为2A,***2为0.5A。如果测试线短路,高低压接反,会熔断***。***熔断后，如果进行测量，在显示“ 正在测量，请等待！ ”后停住。请关机，更换相同容量的***，重测。
2.连线要保持接触良好。仪器应良好接地！
3.仪器的工作场所应远离强电场、强磁场、高频设备。供电电源干扰越小越好，宜选用照明线,如果电源干扰还是较大，可以由交流净化电源给仪器供电。交流净化电源的容量大于200VA即可。
4.仪器工作时，如果出现液晶屏显示紊乱，按所有按键均无响应，或者测量值与实际值相差很远，请按复位键,或者关掉电源,再重新操作。
5.显示器没有字符显示,或颜色很淡,请调节亮度电位器至合适位置。
亮度电位器是多圈电位器 ，有10圈！
6.仪器应存放在干燥通风处，如果长期不用或环境潮湿，使用前应加长预热时间，去除潮气。
7.通讯口调试时使用。
Product introduction
When using this radio bridge to measure the transformer ratio, the operation procedure is complex, the measuring measure range is narrow, which is no longer meet modern fast-paced, high-efficiency requirements. Therefore, NABZ electrical uses the modern electronic technology, developed a new generation of automatic variable ratio group tester. It is ***all, light, high accuracy and with good stability. It uses a large-screen character display, menu operation, friendly interface. The variable group can measure at once. NABZ Automatic variable ratio group tester is ideal product for electrical industry department.
Also called name
Transformer ratio group tester, transformer ratio tester, transformer ratio automatic tester, automatic transformer ratio tester, transformer ratio group testing device, transformer ratio testing device, transformer ratio automatic testing device.
The Characteristics of the products
1. Automatic measurement wiring group.
2. Automatic group transformation.
3. Automatic switching phase sequence.
4. Automatic shift ranging.
5. Automatic calibration.
6. Input the standard ratio, it can automatically calculate the relative error.
7.When the measurement is completed, it can cut off the testing voltage automatically .
8. Setting the data, the measured results can be s***ed automatically, and can be view the previous data.
9. Measuring loaded transformer ratio, only need to enter once
The parameters of the products
1. Ratio measuring range: 1-10000
2. Group:1-12:00
3. Accuracy: 1-1000 0.2 grade,1000-10000 0.5 grade
4. Power supply: AC220V &plu***n; 10%, 50HZ
5. Operating temperature: -5 ℃ ─ 40 ℃
6. Operating humidity: <85%
7. Volume: 430mm × 320mm × 215mm
8. Weight: 8Kg
Power supply: AC110V/115V/120V/127V/220V/230V/240V optional
Input frequency: 50Hz/60Hz optional
Note: The users can select the corresponding power which based on their local supply voltage and frequency, and we will confirm it before the delivery (or inform us that the goods will be used in which country advance)