进口齿轮油泵/gear pumps/德国品质
德国KAYSEN凯森进口齿轮油泵概述
本系列齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。齿轮油泵适用于输送不含固体颗粒和纤维，无腐蚀性，温度不高于80℃，粘度为5×10-6～1.5×10-3m2/s (5-00cSt)的润滑油或性质类似润滑油的其他液体。
主要特点：
1、齿轮油泵使用规定电压
线路电压不超过抽液泵铭牌上所规定电压的&plu***n;10%方可使用。
2、齿轮油泵如何装备
开箱后按结构示意图装配，接上电动机
（1）并紧接连电机
（2）使之泵体与电机为一体
（3）上接好出水轮管
3、齿轮油泵使用前检查各部件外型完好才能开机使用。
4、齿轮油泵不宜作空运转，使用时，抽吸完毕，即停泵，否则会加速叶轮密封件轴承等磨损。也可能磨损泵管，因本泵电机空载转速可达10000转/分。
5、齿轮油泵及时调换电刷，电刷磨损到将不能使用时，须及时调换（2只电刷同时调换）否则会使电刷与换向器接触不良引起坏损，损坏换向器，严重时会烧坏电枢。
6、齿轮油泵在下列情况下不得使用，在使用过程中如发现绝缘损坏，电源线工电缆护套***，插头插座开裂或接触不良，以及断续运转，出现严惩火花等故障时，电机外壳操作时，应立即进行修理。在未修复前不得使用。
7、齿轮油泵防止过载，使用时，凡遇转速异常或降低时，应即停机检查是否有杂物卡住叶轮或电机是否发生故障，抽液泵因故刹车时必须立即切断电源
8、齿轮油泵使用工具要爱惜，所有抽涂泵要小心轻放避免受到冲击。
主要优点：
●齿轮经热处理有较高的硬度和强度，与轴一同安装在可更换的轴套内运转。泵内全部零件的润滑均在泵工作时利用输出介质而自动达到。
●泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力***小，因此轴承负荷小，磨损小，泵效率高。
●泵设有安全阀作为超载保护，安全阀的全回流压力为泵额定排除压力的1.5倍，也可在允许排出压力范围内根据实际需要另外调整。但注意本安全阀不能作减压阀的长期工作，需要时可在管路上另行安装。 从主轴外端向泵看，为顺时针旋转。
主要应用：
●在输油系统中可用作传输、增压泵
●在燃油系统中可用作输送、加压、喷射的燃油泵
●在一切工业领域中，均可作润滑油泵用
Germany KAYSEN imported gear oil pump overview
This series of gear pumps mainly c***ists of gears, shafts, pump bodies, safety valves and shaft end seals. Gear oil pump is suitable for conveying lubricating oil without solid particles and fibers, non-corrosive, temperature not higher than 80 ° C, viscosity of 5×10-6～1.5×10-3m2/s (5-00cSt) or similar lubrication Other liquids of oil.
main feature:
1, the gear oil pump uses the specified voltage
The line voltage shall not exceed &plu***n;10% of the voltage specified on the pumping pump nameplate.
2. How to equip the gear pump
After unpacking, assemble according to the structural diagram and connect the motor
(1) and immediately connected to the motor
(2) Make the pump body and the motor integrated
(3) Connect the water wheel tube
3. Before using the gear oil pump, check that the external parts of the components are in good condition before they can be used.
4. The gear oil pump should not be operated at idle. When using, the pumping is completed, that is, the pump is stopped, otherwise the bearing of the impeller seal will be accelerated. It is also possible to wear the pump tube because the pump motor has a no-load speed of 10,000 rpm.
5. The gear oil pump will change the brush in time. When the brush is worn and will not be used, it must be replaced in time (2 brushes are exchanged at the same time). Otherwise, the brush and the commutator may cause bad damage and damage the commutator. The armature will be burned out.
6. The gear oil pump should not be used under the following conditi***. If the insulation damage is found during the use, the power cable sheath is broken, the plug and socket are cracked or the contact is bad, and the operation is intermittent, and the motor casing is operated when there is a serious punishment for sparks. Repairs should be made immediately. Do not use until unrepaired.
7. The gear oil pump prevents overload. When it is used, when the speed is abnormal or reduced, it should be stopped to check if there is any debris stuck in the impeller or the motor is faulty. If the pump is braked, the power must be cut off immediately.
8, gear oil pump use tools to be cherished, all pumping pumps should be handled with care to ***oid impact.
The main advantage:
●The gear has high hardness and strength after heat treatment, and it is installed in the replaceable bushing together with the shaft. Lubrication of all parts in the pump is automatically achieved with the output medium while the pump is operating.
●The pump has a well-designed oil drain and oil return groove, which is the ***allest torque force that the gear can bear during work. Therefore, the bearing load is ***all, the wear is ***all, and the pump efficiency is high.
● The pump is equipped with a safety valve as overload protection. The full return pressure of the safety valve is 1.5 times the rated pressure of the pump. It can also be adjusted according to actual needs within the allowable discharge pressure range. However, note that this safety valve cannot be used for long-term work of the pressure reducing valve. It can be installed separately on the pipeline when needed. Seen from the outer end of the spindle to the pump, it rotates clockwise.
main application:
●Can be used as tran***ission and booster pump in oil transportation system
●Can be used as fuel pump for conveying, pressurizing and spraying in fuel system
●Can be used as lubricating oil pump in all industrial fields