进口氟塑料管道泵/Pipeline pump/德国品质
德国KAYSEN凯森进口氟塑料管道泵概述
氟塑料管道泵属单级单吸立式结构离心泵，进出口相同并在同一直线上。其过流部件全部为内衬氟塑料（F46）。该泵采用目前***为***的外装式四氟波纹管机械密封，对于输送含杂质颗粒介质时，可配用无冷却水单端面硬对硬（碳化硅对碳化硅）机械密封，所以用户选型时需考虑到介质中的固体含量。
主要特点：
氟塑料管道泵是通过氟塑料热熔融模压工艺制造，具有特强的耐腐 蚀性能的新型管道离心泵。该泵叶轮通过支架与电机直联，结构紧凑， 选用波纹管外装式机械密封，轴封稳定可靠，直观易调。水力性能优越， 吸入口过度均匀，过流部件采用全氟材料(FEP、PFA)制造，耐腐性能 ***。具有耐腐、耐温、不老化、运行平稳、噪音低、效率高、维护方 便、使用寿命长等优点。
主要应用：
氟塑料管道泵供输送或增压酸、碱、***、强氧化剂等强腐蚀性介质之用。适用于工业生产排输液体、高层槽罐增压输送介质、园林喷灌、消防增压、远距离输送、暖通制冷循环、浴室等冷暖水循环增压及设备配套，使用温度-50℃至200℃。
氟塑料管道泵运行注意事项
一、轴承工作是否正常
1. 油温:不要超过60℃。 2.油位:无油环的滚动轴承，油面应不低于滚珠中心;有油环的轴承，油面应能埋浸油环直径的五分之一。为了监视油位，轴承上设有油面计或油标。 3.油质情况:不能进水进杂质，不能乳化或变黑。 4.有否异音:特别是滚动轴承，损坏时一般会出现异常声音。 氟塑料泵运行中
二、真空表、压力表、电流表读数是否正常
1.真空表指针不能摆动过大，如摆动过大有可能是入口发生了汽化。另外真空表读数也不能过高，过高可能是入口门堵塞卡住、或入口门瓣脱落、吸水池水位降低等。 2.压力表读数过低，可能是泵内部件工作不良、密封环严重磨损等。另外系统需水量大时，泵出口压力也会降低。 3.电流表读数过大，可能是供水量大、泵内发生了摩擦等。如电流表读数过小，说明泵已落水或外界不需要那么多的水量。
三、泵体是否有振动
氟塑料泵的振动幅度一般不超过0.08毫米。振动原因有: 1.氟塑料泵和电机的中心不正。 2.泵体或电机的地脚螺丝松动，或基础不牢固。 3.轴承盖紧力不够。使轴瓦在体内出现了跳动。 4.转子质量不平衡。 5.蜗壳泵，特别是有些高扬程的蜗壳泵，在小流量时，也会有不同程度的振动，这是因为此时转子上有径向力的作用。在出口阀门开启到一定大时，振动即行消失。
四、填料工作是否正常
1. 应能稍许滴水，不要过紧，否则会发热冒烟。但过松也会大量漏水，容易窜到轴承里使油乳化。
2.应定期更换填料，发硬了就不起轴封作用。浸泡时间长了也会使填料槽烂。
Germany KAYSEN imported fluoroplastic pipeline pump overview
The fluoroplastic pipeline pump is a single-stage single-suction vertical structure centrifugal pump with the same inlet and outlet and on the same line. The overcurrent components are all lined with fluoroplastic (F46). The pump adopts the most advanced externally mounted PTFE corrugated pipe mechanical seal. It can be used with a non-cooling water single-end hard-to-hard (silicon carbide-silicon carbide) mechanical seal for conveying medium containing impurity particles, so when selecting the user The solids content in the medium needs to be c***idered.
main feature:
The fluoroplastic pipeline pump is a new type of pipeline centrifugal pump which is manufactured by the fluoroplastic hot melt molding process and has excellent corrosion resistance. The pump impeller is directly connected with the motor through the bracket, and has a compact structure. The bellows is externally mounted mechanical seal, and the shaft seal is stable and reliable, and is intuitive and easy to adjust. Excellent hydraulic performance, excessively uniform suction port, and over-current components made of perfluorinated materials (FEP, PFA) for excellent corrosion resistance. It has the advantages of corrosion resistance, temperature resistance, non-aging, stable operation, low noise, high efficiency, convenient maintenance and long service life.
main application:
Fluoroplastic tubing pumps are used to transport or pressurize highly corrosive media such as acids, bases, organic solvents, and strong oxidants. Applicable to industrial production and drainage liquid, high-pressure tank pressurized conveying medium, garden sprinkler irrigation, fire booster, long-distance transportation, HVAC refrigeration cycle, bathroom and other cold and warm water circulation pressurization and equipment matching, use temperature -50 ° C to 200 ° C .
Fluoroplastic pipeline pump operation precauti***
First, the bearing work is normal
1. Oil temperature: Do not exceed 60 °C. 2. Oil level: Rolling bearing without oil ring, the oil surface should not be lower than the center of the ball; for bearings with oil ring, the oil surface should be able to bury one-fifth of the diameter of the oil ring. In order to monitor the oil level, there is a oil level gauge or oil mark on the bearing. 3. Oil quality: Do not enter the water into the impurities, can not be emulsified or blackened. 4. Is there any abnormal sound: especially the rolling bearing, abnormal sound usually occurs when it is damaged. Fluoroplastic pump in operation
Second, vacuum table, pressure gauge, ammeter reading is normal
1. The vacuum gauge pointer cannot be swung too large. If the swing is too large, it may be that the inlet has vaporized. In addition, the reading of the vacuum gauge should not be too high. If the temperature is too high, the entrance door may be jammed, or the entrance door flap may fall off, and the water level of the suction pool may be lowered. 2. The pressure gauge reading is too low, which may be caused by poor operation of the pump components and severe wear of the seal ring. In addition, when the system requires a large amount of water, the pump outlet pressure will also decrease. 3. The ammeter reading is too large, it may be a large amount of water supply, friction inside the pump, etc. If the ammeter reading is too ***all, it means that the pump has fallen into the water or the outside world does not need as much water.
Third, the pump body has vibration
The vibration amplitude of the fluoroplastic pump generally does not exceed 0.08 mm. The causes of vibration are: 1. The center of the fluoroplastic pump and motor is not correct. 2. The anchor screw of the pump body or motor is loose, or the foundation is not strong. 3. The bearing cover is not tight enough. The bearing bush appears to be bouncing in the body. 4. The rotor mass is not balanced. 5. The volute pump, especially some high-lift volute pumps, will h***e different degrees of vibration at low flow rates because of the radial force on the rotor. When the outlet valve opens to a certain height, the vibration disappears.
Fourth, the filler work is normal
1. It should be able to drip slightly, not too tight, otherwise it will heat up and ***oke. However, if it is too loose, it will leak a lot of water, and it is easy to get into the bearing to emulsify the oil.
2. The packing should be replaced regularly. If it is hard, it will not seal the shaft. A long soaking time will also cause the packing groove to rot.