每个人都知道南京NSK轴承设备应该使用***的东西，但是当使用***的东西时，我们应该注意操作方法。否则，只会出现另一个问题，即操作不规范，导致轴承装置错误或设备不***。下一步是如何对齐轴。这个装置怎么样？
Everyone knows that Nanjing NSK bearing equipment should use professional things, but when using professional things, we should pay attention to the method of operation. Otherwise, there will only be another problem, that is, the operation is not standardized, resulting in bearing device errors or imprecise equipment. The next step is how to align axes. How about this device?
二是考虑误差补偿。即使提高了南京NSK轴承两端的旋转精度，也可以部分消除两个支承部件与轴颈两端之间的同轴度误差。内孔采用喷砂、小直径、小塞子强化，提高了匹配精度。
The two is to c***ider error compensation. Even if the rotation accuracy of the two ends of Nanjing NSK bearing is improved, the coaxiality error between the two supporting parts and the two ends of journal can be partly eliminated. The inner hole is strengthened by sandblasting, ***all diameter and ***all stopper, which improves the matching accuracy.
为了提高南京NSK轴承装配精度，需要通过测量方法和非测量对象来测量轴承孔和外圆的协调外尺寸。通过测量轴承，可以测量轴承内径和外径的所有测量项目，并可以对测量数据进行深入分析。在此基础上，对薄壁轴和座孔精密南京NSK轴承装置的位置进行了测量。在实践中，匹配轴和座圈的相应尺寸和几何形状应在与轴承相同的温度下测量。
In order to improve the assembly precision of Nanjing NSK bearing, the coordinated outer dimensi*** of bearing hole and outer circle need to be measured by measuring methods and non-measuring objects. By measuring the bearing, all measuring items of the bearing inner diameter and outer diameter can be measured, and the measured data can be analyzed in depth. On this basis, the position of the precision Nanjing NSK bearing device for thin-walled shaft and seat hole is measured. In practice, the corresponding size and geometry of the matching shaft and seat ring should be measured at the same temperature as the bearing.
为了保证高的实际配合，轴和座孔的粗糙度应尽可能小。
In order to ensure high practical coordination, the roughness of shaft and seat hole should be as ***all as possible.
在上述测量中，南京NSK轴承的外圆和内孔分别代表两个非常大的误差方向符号，分别位于相应的表面和倒角轴和阀座孔附近。在实际安装过程中，在同一方向上总误差较大的误差被对准在一起，从而在安装后部分误差被部分抵消。
In the above measurement, the outer circle and inner bore of Nanjing NSK bearing represent two very large error direction symbols, which are located near the corresponding surface, chamfered shaft and seat bore respectively. In the actual installation process, the errors with larger total errors in the same direction are aligned together, so that some errors are partially offset after installation.
进口轴承应在什么情况下清洗？进口南京NSK轴承在运行中，如果没有统一的规律，不规则的“压力”声，这时应该进行清洗轴承或重新润滑轴承或更换润滑剂，***不能统一定律，不规则的“按”声方法。
Under what circumstances should the imported bearings be cleaned? Imported Nanjing NSK bearings in operation, if there is no uniform law, irregular "pressure" sound, at this time should be carried out to clean bearings or re-lubricate bearings or replace lubricants, absolutely can not unify the law, irregular "according" sound method.
文章来自：南京SKF轴承 www.wh-
The article is from: Nanjing SKF bearing www.wh-
文章来自：南京INA轴承 a-
The article is from: Nanjing INA bearing a-
文章来自：南京NSK轴承
The article is from: Nanjing NSK bearing
***：524085168
电话：0510-81207777
手机：13311666672