企业资质

东莞市晶宏塑胶原料有限公司

普通会员8
|
企业等级:普通会员
经营模式:经销批发
所在地区:广东 东莞
联系卖家:蒋珂
手机号码:18200646066
公司官网:www.jhsj.cpooo.com
企业地址:东莞市樟木头镇
本企业已通过工商资料核验!
企业概况

东莞市晶宏塑胶位于中国广东省东莞市樟木头镇塑胶城,经营各种工程,通用塑料原料为买卖对象的专ye塑料原料贸易商,我们不生产原料,只做专ye的供应商。公司自成立以来,积极倡导“诚信如同生命,口碑重于泰山”的经营理念,竭诚为广大新老客户提供you质的服务。...

POM AW-09日本宝理

产品编号:1714381288                    更新时间:2020-07-29
价格: ¥1.00
东莞市晶宏塑胶原料有限公司

东莞市晶宏塑胶原料有限公司

  • 主营业务:工程塑料、弹性体
  • 公司官网:www.jhsj.cpooo.com
  • 公司地址:东莞市樟木头镇

联系人名片:

蒋珂 18200646066

联系时务必告知是在"产品网"看到的

产品详情

POM AW-09日本宝理---POM塑胶原料加工时料筒温度过高,POM的热稳定性差,温度过高或时间过长,均会引起分解,致使制品性能下降,特别是温度超过250℃,分解速度会加快,并溢出强烈刺激眼睛的甲醛气体,严重时制品会产生气泡或变色。而且,由于POM属切敏性聚合物,熔体的流动性在熔点以上对温度变化不明显,而对剪切速率较为敏感,因此,仅靠提高POM的温度来改善其流动性的效果是有限的。在成型薄壁制品时,一般建议采用熔体流动速率较高的POM品级。均聚POM的熔融温度为175℃,由于既要考虑其熔融温度而设定较高的温度,又要尽可能防止其热分解而设定较窄的温度范围,因此可将树脂温度设定在190~200℃。共聚POM的熔融温度为165℃,由于加工窗口相对较宽,因此,在***成型时可将树脂温度设定在180~200℃。

 

When processing POM plastic raw materials, if the barrel temperature is too high, the thermal stability of POM is poor, if the temperature is too high or the time is too long, the decomposition will be accelerated, especially when the temperature is over 250 ℃, the decomposition speed will be accelerated, and formaldehyde gas which strongly irritates the eyes will overflow. In serious cases, the product will produce bubbles or discoloration. Moreover, because POM is a shear sensitive polymer, the fluidity of POM is not obvious to the temperature change above the melting point, but sensitive to the shear rate. Therefore, only increasing the temperature of POM to improve its fluidity is limited. POM grade with higher melt flow rate is generally recommended for thin-walled products. The melting temperature of homopolymerized POM is 175 ℃. The resin temperature can be set between 190 ℃ and 200 ℃ because a higher temperature should be set c***idering its melting temperature and a narrow temperature range should be set to prevent its thermal decomposition as far as possible. The melting temperature of copolymerized POM is 165 ℃, and the resin temperature can be set at 180 ~ 200 ℃ during injection molding due to the relatively wide processing window.

 

POM AW-09日本宝理的物理性能

额定值 单位制 测试方法
密度 1.37 g/cm³ ISO 1183
熔流率(熔体流动速率) (190°C/2.16 kg) 3.0 g/10 min ISO 1133
溶化体积流率(MVR) (190°C/2.16 kg) 2.50 cm³/10min ISO 1133
吸水率 (23°C, 24 hr) 0.70 % ISO 62
硬度 额定值 单位制 测试方法
洛氏硬度 (M 计秤) 70  ISO 2039-2
机械性能 额定值 单位制 测试方法
拉伸模量 2200 MPa ISO 527-2
拉伸应力 54.0 MPa ISO 527-2
标称拉伸断裂应变 30 % ISO 527-2
弯曲模量 2050 MPa ISO 178
弯曲应力 70.0 MPa ISO 178
摩擦系数 - Dynamic   JIS K7218
    -- 1 0.300  JIS K7218
    -- 2 0.160  JIS K7218

东莞市晶宏塑胶原料有限公司电话:0769-89977070传真:0769-89977070联系人:蒋珂 18200646066

地址:东莞市樟木头镇主营产品:工程塑料、弹性体

Copyright © 2025 版权所有: 产品网店铺主体:东莞市晶宏塑胶原料有限公司

免责声明:以上所展示的信息由企业自行提供,内容的真实性、准确性和合法性由发布企业负责。产品网对此不承担任何保证责任。