 产 品 说 明 |
|||||||||||||||||||||||||||||||||||||||||||||||||
|
1.規格型***和安規認***
MODEL NUMBER AND SAFETY CERTIFICATION
1-1 品名規格：系列***+***定***流+***定***壓+認***符***
Model Number: Part Number+Rated Current+Rated Voltage+Approvals.
例子[example]:
3GFU 1A 250V 1)系列*** Part Number
2)***定***流 Rated Current
1） 2） 3） 3)***定***壓 Rated Voltage
1-2 ***定***流和***定***壓
Rated Current And Voltage
***定***流： 100mA~10A
Rated Current: 100mA~10A
***定***壓;125V/250V AC
Rated Voltage:125V/250V AC
1-3標示Marking
保險絲上需有下列標示
The fuse shall h***e the following marking:
規格：特性符***+***定***流+***定***壓
Specification:Characteristic Symbol+Rated Voltage
100mA~800mA : _mA250V 1A~10A:_A250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals
100mA~10A:
注意：對標示字樣大小沒有規定
Note:Size of the markings h***e not be specified.
2.適用範圍
SCOPE
適用於一般***子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRUCTURE
3-1 工程圖（***位：mm）
Outline Drawing and Dimensi***(Unit:mm)
3-2結構
Structure
4.外觀及形狀
APPEARANCES AND CONFIGURATION
4-1外觀：不應有破碎、明顯的汙斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形狀：帶腳的保險絲
Configuration:Axial Leaded Fuse.
5.物理特性
PHYSICAL CHARACTERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力，持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.******特性
ELECTRICAL CHARACTERISTICS
熔斷/***流特性：
Pre-Arcing Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag and Fast Acting)
b、Electrical characteristics
Time Lag
Fast Acting
c、Temperature character
When 100% of rating the temperature rise doesn’t exceed 75℃.
d、Approvals
7.環境特性
ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
Operating Temperature: -5℃~60℃
7-2 保存條件
Storage Conditi***
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On ***erage, It can be stored below the relative humidity or 75% for 3 years.
在非露天下，相對濕度為95%下***多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
W***e Solder
焊接溫度：260&plu***n;5℃
Soldering Temperature:260&plu***n;5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350&plu***n;5℃
Soldering Temperature: 350&plu***n;5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER NOTICE IN USING
如果需在保險絲上加***縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.
|
|||||||||||||||||||||||||||||||||||||||||||||||||
