***环保型汽车底盘装甲诚招省级***
河北省 江苏省 上海市 北京市 安徽省 河南省 山西省 天津市 浙江省 辽宁省
招商电话15588610888 李经理
本公司研发的***新一代***大政牌环保型汽车底盘装甲，是采用***的聚氨酯合成技术，由高分子聚氨酯弹性体合成的，***低气味，对******无害，符合国际环保标准。我公司致力于打造中国底盘装甲的***品牌，为您的爱车提供持久保护，提高行车安全。
The advanced chassis protection (Polymer polyurethane elastomer) of brand Da Zheng developed by our company adopts the Germany advanced PU synthetic technology; and the chassis protection synthesized by polymer polyurethane elastomer, no toxicity & low odor, meets the international environmental standa***. And the product can provide lasting protection for your car and improve your road safety.Leading level in domestic & overseas
高弹性 high elasticity
高附着力 high adhesion
阻燃防锈 flame & rust retardant
隔热防寒 heat insulation & cold-proof
隔声降噪 Noise reduction
防撞击 Anti-collision
防震 anti-vibration
我司生产的底盘装甲具备的优异性能大大优越于目前市场销售的沥青，橡塑类等汽车底盘装甲产品，本公司生产的汽车底盘装甲有效成分高，一次喷涂的装甲厚度可达2mm，喷一次即可满足所需要求。这样大大降低了消费成本，提高工作效率。
The performance of the chassis produced in our company is greatly superior to the bituminous & rubber based products. The products we produced, with high content of active c***tituent, the spraying thickness can reach 2mm for one-time spraying, and one-time spraying can meet all your need. So the
c***umption can be reduced greatly and the work efficiency can also be
improved.
适用范围
适用于各类车辆的底盘，轮弧，汽车大梁，油箱壳，叶子板内侧，发送机罩，后备箱底部等。
Scope of application
It is applicable to the chassis of all kinds of vehicles, fender trim, automotive frame, tank shell, fender inside, tran***itter cover and bottom of trunk etc.
产品性能
本品在240度至-50度范围内无变软变脆现象，且本品耐热，耐寒，耐潮湿，耐水泡，并可有效阻隔寒暑对车内温度的影响，充分体现其优良的性能和强附着力；
另外，本品防锈能力***，且弹性强、韧性好、抗撕裂，可完全***砂石对车辆底盘的撞击，大幅度降低轮胎与路面摩擦产生的噪音。
Product performance
In the temperature scope of 240~ -50°, the product without softening & brittleness phenomenon, and with good performances of heat resistance, cold resistant, moisture resistance, and blister resistance; it can impede the effect ( in- car temperature) caused by cold & heat effectively, which fully embodies the good performance and strong adhesion of the product; in addition, the product with excellent anti-rust capability, strong elasticity & toughness and highly tear resistant, which can completely resist the impaction on chassis from dinas and significantly reduce the noise caused by the friction between tyre & p***ement.
施涂说明
1. 喷涂前彻底清洁汽车底盘，去除锈迹，污渍，油脂，蜡质等。并覆盖保护无需喷涂的部位。
2. 本聚氨酯弹性体，为湿固化高聚物。开瓶后表面有初固化膜。将喷枪直接插入罐中然后旋紧，充分摇匀，连接压力为0.04mpa-0.06mpa压缩空气，然后即可喷涂。
3. 本品具有优良的触变性，无滴挂现象；固化时间，春季 2-3小时；冬季6-8小时。夏季速干时间为15分钟，15分钟后，即可行车。冬季喷涂1小时后即可行车。完全固化时间为8-12小时，固化后，表面光滑无粘性。且具有强韧弹性。4. 喷涂完毕请用专用清洗剂将喷枪清洗干净即可。
Application instruction
1. Before application, clean the automotive chassis completely to remove rust, dirty mark, grease and waxes etc.； and protect the area not to be sprayed.
2. The product is moisture curing polymer, which is with a layer of cured film on surface after opening. Insert spraying gun into the pot directly, tighten the pot and shake fully, then spray; the connection pressure is 0.04mpa-0.06mpa (compressed air).
3. The product is with good thixotropy, without sagging; the curing time is 2~3h in spring and 6~8h in winter. The quick drying time is 15mins in spring, and the car can be driven after 15 mins, and in summer, the car can be driven after 1 hour. The complete curing time of product is 8-12 h; after curing, the surface is ***ooth, without viscosity; and with good toughness & elasticity.
4. The spraying gun shall be cleaned with special cleaning agent after spraying.