型号：PA612 Zytel FE5382 BK276
性能：玻璃纤维增强级，33%玻璃纤维增强，热稳定，黑色聚酰胺612树脂，抗紫外线。
Zytel PA物性如需要完整物性联系我们
| Secant Modulus | 2.57506 GPa @Strain 4.49 %, Temperature 40.0 °C |
373.487 ksi @Strain 4.49 %, Temperature 104 °F |
50%RH; ISO 11403-1 -2 | ||
| 3.02897 GPa @Strain 4.35 %, Temperature 23.0 °C |
439.322 ksi @Strain 4.35 %, Temperature 73.4 °F |
50%RH; ISO 11403-1 -2 | |||
| 3.35944 GPa @Strain 3.23 %, Temperature 40.0 °C |
487.253 ksi @Strain 3.23 %, Temperature 104 °F |
50%RH; ISO 11403-1 -2 | |||
| 3.85392 GPa @Strain 3.19 %, Temperature 23.0 °C |
558.973 ksi @Strain 3.19 %, Temperature 73.4 °F |
50%RH; ISO 11403-1 -2 | |||
| 4.10759 GPa @Strain 2.24 %, Temperature 40.0 °C |
595.765 ksi @Strain 2.24 %, Temperature 104 °F |
50%RH; ISO 11403-1 -2 | |||
| 4.53477 GPa @Strain 3.94 %, Temperature 0.000 °C |
657.723 ksi @Strain 3.94 %, Temperature 32.0 °F |
50%RH; ISO 11403-1 -2 | |||
| 4.59911 GPa @Strain 2.25 %, Temperature 23.0 °C |
667.055 ksi @Strain 2.25 %, Temperature 73.4 °F |
50%RH; ISO 11403-1 -2 | |||
| 4.96439 GPa @Strain 1.32 %, Temperature 40.0 °C |
720.035 ksi @Strain 1.32 %, Temperature 104 °F |
50%RH; ISO 11403-1 -2 | |||
| 5.5688 GPa @Strain 1.25 %, Temperature 23.0 °C |
807.70 ksi @Strain 1.25 %, Temperature 73.4 °F |
50%RH; ISO 11403-1 -2 | |||
| 5.85795 GPa @Strain 2.83 %, Temperature 0.000 °C |
849.637 ksi @Strain 2.83 %, Temperature 32.0 °F |
50%RH; ISO 11403-1 -2 | |||
| 5.89067 GPa @Strain 3.75 %, Temperature -20.0 °C |
854.383 ksi @Strain 3.75 %, Temperature -4.00 °F |
50%RH; ISO 11403-1 -2 | |||
| 6.07879 GPa @Strain 0.330 %, Temperature 40.0 °C |
881.668 ksi @Strain 0.330 %, Temperature 104 °F |
50%RH; ISO 11403-1 -2 | |||
| 6.43 GPa @Strain 0.300 %, Temperature 23.0 °C |
933 ksi @Strain 0.300 %, Temperature 73.4 °F |
50%RH; ISO 11403-1 -2 | |||
| 6.53536 GPa @Strain 2.63 %, Temperature 40.0 °C |
947.889 ksi @Strain 2.63 %, Temperature 104 °F |
DAM; ISO 11403-1 -2 | |||
| 6.80144 GPa @Strain 2.08 %, Temperature 0.000 °C |
986.481 ksi @Strain 2.08 %, Temperature 32.0 °F |
50%RH; ISO 11403-1 -2 | |||
| 6.91678 GPa @Strain 3.04 %, Temperature 23.0 °C |
1003.21 ksi @Strain 3.04 %, Temperature 73.4 °F |
DAM; ISO 11403-1 -2 | |||
| 7.1739 GPa @Strain 3.18 %, Temperature 0.000 °C |
1040.5 ksi @Strain 3.18 %, Temperature 32.0 °F |
DAM; ISO 11403-1 -2 | |||
| 7.36823 GPa @Strain 2.77 %, Temperature -20.0 °C |
1068.69 ksi @Strain 2.77 %, Temperature -4.00 °F |
50%RH; ISO 11403-1 -2 | |||
| 7.45238 GPa @Strain 3.36 %, Temperature -20.0 °C |
1080.89 ksi @Strain 3.36 %, Temperature -4.00 °F |
DAM; ISO 11403-1 -2 | |||
| 7.76968 GPa @Strain 1.88 %, Temperature 40.0 °C |
1126.91 ksi @Strain 1.88 %, Temperature 104 °F |
DAM; ISO 11403-1 -2 | |||
| 7.85214 GPa @Strain 1.40 %, Temperature 0.000 °C |
1138.87 ksi @Strain 1.40 %, Temperature 32.0 °F |
50%RH; ISO 11403-1 -2 | |||
| 8.11161 GPa @Strain 2.24 %, Temperature 23.0 °C |
1176.51 ksi @Strain 2.24 %, Temperature 73.4 °F |
DAM; ISO 11403-1 -2 | |||
| 8.27107 GPa @Strain 2.42 %, Temperature 0.000 °C |
1199.64 ksi @Strain 2.42 %, Temperature 32.0 °F |
DAM; ISO 11403-1 -2 | |||
| 8.3881 GPa @Strain 2.10 %, Temperature -20.0 °C |
1216.6 ksi @Strain 2.10 %, Temperature -4.00 °F |
50%RH; ISO 11403-1 -2 | |||
| 8.71193 GPa @Strain 2.43 %, Temperature -20.0 °C |
1263.58 ksi @Strain 2.43 %, Temperature -4.00 °F |
DAM; ISO 11403-1 -2 | |||
| 8.78855 GPa @Strain 1.31 %, Temperature 40.0 °C |
1274.69 ksi @Strain 1.31 %, Temperature 104 °F |
DAM; ISO 11403-1 -2 | |||
| 9.00307 GPa @Strain 1.63 %, Temperature 23.0 °C |
1305.81 ksi @Strain 1.63 %, Temperature 73.4 °F |
DAM; ISO 11403-1 -2 | |||
| 9.08415 GPa @Strain 1.83 %, Temperature 0.000 °C |
1317.57 ksi @Strain 1.83 %, Temperature 32.0 °F |
DAM; ISO 11403-1 -2 | |||
| 9.13115 GPa @Strain 0.610 %, Temperature 0.000 °C |
1324.38 ksi @Strain 0.610 %, Temperature 32.0 °F |
50%RH; ISO 11403-1 -2 | |||
| 9.48913 GPa @Strain 1.84 %, Temperature -20.0 °C |
1376.30 ksi @Strain 1.84 %, Temperature -4.00 °F |
DAM; ISO 11403-1 -2 | |||
| 9.51181 GPa @Strain 1.44 %, Temperature -20.0 °C |
1379.59 ksi @Strain 1.44 %, Temperature -4.00 °F |
50%RH; ISO 11403-1 -2 | |||
| 9.75932 GPa @Strain 0.590 %, Temperature 40.0 °C |
1415.49 ksi @Strain 0.590 %, Temperature 104 °F |
DAM; ISO 11403-1 -2 | |||
| 9.82968 GPa @Strain 0.822 %, Temperature 23.0 °C |
1425.70 ksi @Strain 0.822 %, Temperature 73.4 °F |
DAM; ISO 11403-1 -2 | |||
| 9.95378 GPa @Strain 1.19 %, Temperature 0.000 °C |
1443.70 ksi @Strain 1.19 %, Temperature 32.0 °F |
DAM; ISO 11403-1 -2 | |||
| 10.3657 GPa @Strain 0.670 %, Temperature 0.000 °C |
1503.44 ksi @Strain 0.670 %, Temperature 32.0 °F |
DAM; ISO 11403-1 -2 | |||
| 10.5672 GPa @Strain 0.640 %, Temperature -20.0 °C |
1532.67 ksi @Strain 0.640 %, Temperature -4.00 °F |
DAM; ISO 11403-1 -2 | |||
| 10.9449 GPa @Strain 0.490 %, Temperature -20.0 °C |
1587.45 ksi @Strain 0.490 %, Temperature -4.00 °F |
50%RH; ISO 11403-1 -2 | |||
| Izod Impact, Notched (ISO) | 12.0 kJ/m² | 5.71 ft-lb/in² | DAM; ISO 180/1A | ||
| 15.0 kJ/m² | 7.14 ft-lb/in² | 50%RH; ISO 180/1A | |||
| 10.0 kJ/m² @Temperature -30.0 °C |
4.76 ft-lb/in² @Temperature -22.0 °F |
DAM; ISO 180/1A | |||
| 10.0 kJ/m² @Temperature -30.0 °C |
4.76 ft-lb/in² @Temperature -22.0 °F |
50%RH; ISO 180/1A | |||
| Charpy Impact Unnotched | 9.00 J/cm² | 42.8 ft-lb/in² | DAM; ISO 179/1eU | ||
| 10.0 J/cm² | 47.6 ft-lb/in² | 50%RH; ISO 179/1eU | |||
| 7.50 J/cm² @Temperature -30.0 °C |
35.7 ft-lb/in² @Temperature -22.0 °F |
50%RH; ISO 179/1eU | |||
| 8.00 J/cm² @Temperature -30.0 °C |
38.1 ft-lb/in² @Temperature -22.0 °F |
DAM; ISO 179/1eU | |||
| Charpy Impact, Notched | 1.50 J/cm² | 7.14 ft-lb/in² | DAM; ISO 179/1eA | ||
| 1.80 J/cm² | 8.57 ft-lb/in² | 50%RH; ISO 179/1eA | |||
| 1.00 J/cm² @Temperature -30.0 °C |
4.76 ft-lb/in² @Temperature -22.0 °F |
DAM; ISO 179/1eA | |||
| 1.00 J/cm² @Temperature -30.0 °C |
4.76 ft-lb/in² @Temperature -22.0 °F |
50%RH; ISO 179/1eA | |||
| Puncture Energy | 6.00 J | 4.43 ft-lb | DAM; ISO 6603-2 | ||
| Tensile Creep Modulus, 1 hour | 8400 MPa @Time 3600 sec |
1.22e+6 psi @Time 1.00 hour |
50%RH; ISO 899-1 | ||
| Tensile Creep Modulus, 1000 hours | 6000 MPa @Time 3.60e+6 sec |
870000 psi @Time 1000 hour |
50%RH; ISO 899-1 | ||
| Electrical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Volume Resistivity | 1.00e+11 ohm-cm | 1.00e+11 ohm-cm | 50%RH; IEC 60093 | ||
| >= 1.00e+15 ohm-cm | >= 1.00e+15 ohm-cm | DAM; IEC 60093 | |||
| Surface Resistance | 1.00e+13 ohm | 1.00e+13 ohm | 50%RH; IEC 60093 | ||
| Dielectric Strength | 31.0 kV/mm | 787 kV/in | 50%RH; IEC 60243-1 | ||
| 36.0 kV/mm | 914 kV/in | DAM; IEC 60243-1 | |||
| Comparative Tracking Index | 400 V | 400 V | DAM; IEC 60112 | ||
| Thermal Properties | Metric | English | Comments | ||
| CTE, linear, Parallel to Flow | 20.0 µm/m-°C | 11.1 µin/in-°F | DAM; ISO 11359-1/-2 | ||
| CTE, linear, Transverse to Flow | 100 µm/m-°C | 55.6 µin/in-°F | DAM; ISO 11359-1/-2 | ||
| Specific Heat Capacity | 2.13 J/g-°C | 0.509 BTU/lb-°F | |||
| Thermal Conductivity | 0.240 W/m-K | 1.67 BTU-in/hr-ft²-°F | of melt | ||
| Melting Point | 262 °C | 504 °F | DAM; 10°C/min; ISO 11357-1/-3 | ||
| Deflection Temperature at 0.46 MPa (66 psi) | 261 °C | 502 °F | DAM; ISO 75-1/-2 | ||
| Deflection Temperature at 1.8 MPa (264 psi) | 252 °C | 486 °F | DAM; ISO 75-1/-2 | ||
| Vicat Softening Point | 255 °C | 491 °F | DAM; 50°C/h 50N; ISO 306 | ||
| Glass Transition Temp, Tg | 80.0 °C | 176 °F | DAM; 10°C/min; ISO 11357-1/-2 | ||
| Flammability, UL94 | HB @Thickness 1.50 mm |
HB @Thickness 0.0591 in |
DAM; IEC 60695-11-10 | ||
| HB @Thickness 0.700 mm |
HB @Thickness 0.0276 in |
DAM; IEC 60695-11-10 | |||
| Oxygen Index | 24 % | 24 % | DAM; ISO 4589-1/-2 | ||
| DeSCRJPTive Properties | |||||
| Additives | Lubricants | ||||
| Release agent | |||||
| Delivery form | Pellets | ||||
| Part Marking Code | >PA66-GF35< | ISO 11469 | |||
| Processing | Injection Moulding | ||||
| Regional Availability | Asia Pacific | ||||
| Europe | |||||
| Global | |||||
| Near East/Africa | |||||
| North America | |||||
| South and Central America | |||||
| Resin Identification | PA66-GF35 | ||||
| Special characteristics | Heat stabilised or stable to heat | ||||
| UL recognition | UL | DAM | |||
Some of the values displayed above may have been converted from their original units and/or rounded in order to display the information in a consistent format. Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units. We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. We also ask that you refer to MatWeb's terms of use regarding this information. Click here to view all the property values for this datasheet as they were originally entered into MatWeb.
Users viewing this material also viewed the following:
DuPont Performance Polymers Zytel® 70G33HS1L NC010 Nylon 66
DuPont Performance Polymers Zytel® 73G30L NC010 Nylon 6
DuPont Performance Polymers Zytel® 70G43L NC010 Nylon 66
DuPont Performance Polymers Zytel® 70G35HSL BK039B Nylon 66
DuPont Performance Polymers Zytel® 70G33L NC010 Nylon 66
TECHNYL A 238C M25 BLACK Nylon 66填充 25%矿物增强特点 导电 热稳定 良好的尺寸稳定性 高耐热性 良好的韧性 低吸湿性形式 黑色 微丸 处理方法 注塑成型
TECHNYL A 238C M25 BLACK 5N Nylon 66 填充 25%矿纤增强添加剂 热稳定剂特点 导电 热稳定 良好的尺寸稳定性 高耐热性 良好的韧性 低吸湿性用途 汽车应用 汽车内饰件 形式 黑色 微丸
TECHNYL A 238P5 M25 BLACK 5N Nylon 66 填充 25%矿物增强特点 导电 良好的表面光泽度 低温耐冲击性 良好的抗冲击性 热稳定 用途 汽车应用 形式 黑色 微丸处理方法 注塑成型
TECHNYL A 246 Nylon 66 添加剂 热稳定剂特点 良好的抗冲击性 热稳定 低温耐冲击性 用途 鞋类 体育用品 玩具形式 黑色 本色 微丸处理方法 注塑成型
TECHNYL A 246M Nylon 66 添加剂 热稳定剂 特点 低温耐冲击性 超高耐冲击性用途 鞋类 玩具 体育用品形式 黑色 本色 微丸处理方法 注塑成型
TECHNYL A 248 MT30 Nylon 66 填充 30%矿物增强特点 抗疲劳 良好的热稳定性 低摩擦 良好的耐化学性 良好的抗紫外线 良好的抗蠕变性 耐磨性形式 微丸处理方法 注塑成型
TECHNYL A 248 V33 BLACK 21 N Nylon 66 填充 33%玻纤增强添加剂 热稳定剂特点 热稳定 高抗冲击性 低温耐冲击性 用途 汽车应用 外壳 汽车引擎盖下 体育用品 形式 黑色 微丸 处理方法 注塑成型
TECHNYL A 268 BLACK 21 N Nylon 66 添加剂 热稳定剂特点 热稳定 高流动 高抗冲击性用途 汽车应用 紧固件形式 黑色 微丸 处理方法 注塑成型
TECHNYL A 302 Nylon 66 特点 高抗冲击性 高粘度 中等刚性 用途 薄壁零件 管道形式 本色 微丸用途 挤压 注塑成型
TECHNYL A 302 V25 BLACK Nylon 66 填充 25%玻纤增强特点 高粘度 形式 黑色 微丸处理方法 挤压 注塑成型等等
零风险购货 10天无理由退换货
为了更好的服务客户，我公司现推出零风险采购方案，你在我公司购买的货物只要发货后10天内。你对货物有任何不满意都可以提出退换申请，在货物未拆封，不影响二次销售的情况下，我司将给你办理退换手续并承担运费，为你免去任何担忧。。