企业资质

上海沃证机电技术服务有限公司

普通会员10
|
企业等级:普通会员
经营模式:
所在地区:上海 上海
联系卖家:
手机号码:
公司官网:www.via-cert.com
企业地址:
本企业已通过工商资料核验!
企业概况

上海沃证机电技术服务有限公司成立于2007年,是致力于为国内企业提供全球各国安全认证、安全检验与测试、培训等的第三方服务机构。主要为国内出口欧洲企业提供测试和认证服务,主要涉及的领域有机械、压力设备、游艇、电梯、建筑材料、电子电器、医疗器械、企业社会责任审核等,同时也提供针对出口俄罗斯和独联体国家的......

户外遮阳产品EN13561欧盟CE认证

产品编号:6760829                    更新时间:2016-06-08
价格: ¥10000.00
上海沃证机电技术服务有限公司

上海沃证机电技术服务有限公司

  • 主营业务:欧盟CE认证_钢结构CE认证_国际焊接认证ISO3834
  • 公司官网:www.via-cert.com
  • 公司地址:

联系人名片:

联系时务必告知是在"产品网"看到的

产品详情

EN-13561 2004是英国标准学会(Britain Standard Institute,简称BSI)制订的关于户外遮阳行业的认证标准,欧盟通用,同时在***的认可度非常高。
Fabric
15.2.1   General
With reference to the initial state, performances shall be estimated after 1000 h exposure to weathering agents according to EN ISO 105-B04.
这个一个通则,以下所有的测试都要基于这个标准,就是按照EN-ISO-105-B04将面料曝晒1000小时,下面各个子项分别测试之前和之后的样品性能数据,并做比较,得出结论。
15.2.2   Colour fastness
The grey scale according to EN 20105-A02 shall be at least at level 4.
这部分是关于色牢度,要求达到级别4,测试标准是EN-20105-A02,由德国标准化学会定制,色牢度共5级别,其中1***低,5***高。
15.2.3   Tensile resistance
-The minimale tensile resistance carried out according to EN ISO 1421 (on strip of 5 cm wide) shall be:
-warp     100 daN
-weft      60 daN
-The reduction of resistance shall not be more than 20 % relative to the initial state.
这部分是关于抗拉力测试,要求经纱方向>=1000N(1daN=10N),纬纱方向>=600N,测试标准是EN-ISO-1421,样品长度为5cm(2 inches)
同时根据15.2.1的测试,曝晒1000小时后,抗拉力的性能跟初始状况相比不能下降超过20%
15.2.4   Dimensional stability
-Stability under weathering agents : dimensional variati*** shall be between the following limits:
-warp [-3 % , +1 %]
-weft : [-1 % , +1 %]
- Residual deformati*** after traction application : dimensional variati*** measured after 24 h loading 250 N on 100 mm, on sample 100 mm x 1 200 mm, warp way and weft according to annex A. shall be within the following limits:
-Total change in length under load:
-warp < 12 mm
-weft < 41 mm
-Residual length, load released:
-warp < 1 mm
-weft < 16 mm
-Residual width, load released:
-warp 0 mm
-weft 0 mm
这部分是形态稳定性的测试,首先是根据15.2.1的测试,经纬向的变化不能超过标准要求;其次是取100mm*1200mm的样品,承受250N的压力,经过24小时,经纬向的变化不能超过标准要求。
15.2.5   Resistance to water penetration:
Resistance to water penetration (Schopper test) shall be measured according to EN 20811. Stitches are not concerned.
A new measurement is taken after simulation of effect of repeated showers.
The sample is immersed during 24 h in demineralized water, changed completely every 3 h.
The reduction of the resistance to water penetration shall not be more than 15 %.
这部分关于防水性能,根据EN-20811标准做喷淋实验,其中接缝部分不做要求。
做完前面的实验后,将样品浸入脱矿物质的水中24小时,每3小时将水更换一遍,跟初始状态相比,防水性能下降不能超过15%

 

上海沃证机电技术服务有限公司电话:传真:联系人:

地址:主营产品:欧盟CE认证_钢结构CE认证_国际焊接认证ISO3834

Copyright © 2025 版权所有: 产品网店铺主体:上海沃证机电技术服务有限公司

免责声明:以上所展示的信息由企业自行提供,内容的真实性、准确性和合法性由发布企业负责。产品网对此不承担任何保证责任。