一、拆屏机性能参数原理

1.概述Introduction
该设备用于触摸屏由于贴合不良或盖板破碎需要把盖板与功能片、功能片与LCM液模组分离开的设备,是电容式触摸屏返修必要的专用设备,原理是将触摸屏固定在夹具上通过温度软化导电胶,再用电机匀速运动将上下两层拉开达到拆屏的目的,采用西门子plc控制温度、速度,拆装方便、操作简单易懂是电容屏返修市场***理想的设备。The equipment is for a touch screen or a bonding failure due to the need to break the cover sheet cover and function, and function of the chip module LCM liquid separated device, a capacitive touch screen repair necessary special equipment, the principle is the touch screen is fixed in the fixture by softening temperature of the conductive adhesive, and then the upper and lower layers of uniform motion motor kicked achieve the purpose of split screen, with Siemens plc control of temperature, convenient speed, accessibility, simple and easy to understand is the ideal market for capacitive screen repair equipment.
二、用途Usage

1、适用于触摸屏钢化玻璃(GISS/CTP)与液晶(LCP/LCM/OLED)分离返修工艺。Suitable for the Touchscreen glass (GISS / CTP) and LCD (LCP / LCM / OLED) separation rework process.
2、 适合:苹果、三星、HTC、小米、HUAWEI、魅族、步步高、OPPO、***、诺基亚、黑莓等品牌机触摸屏返修。Suitable brand: Apple, Samsung, HTC, millet, HUAWEI, Meizu, backgammon, OPPO, ***, Nokia, Blackberry and other brand touch screen repair.
三、设备参数 Equipment Parameters
1.西门子PLC(带温控模块)一套
Simens PLC one set(with the temperature control module).
2.57步进电机两套。
57 step motors two sets.
3.8寸信捷触控屏。
8 inch XINJIE touchscreen.
4.真空泵一套。
Vaccum pump one set.
5.发热管600W一套。400W两套
Heating pipe 600W one set; 400W two sets.
6.欧姆龙的真空电子表2个
Omron vaccum electric meter 2 pcs.
7.负压阀,泄压阀各两套
Negative pressure valve, pressure relief valve each two sets.
四、技术参数 Technique parameters
1.工作周期:3min/PCS
Working cycle: 3min/PCS
2.工作温度:RT~50℃
Working temperature: RT~50℃
3.温度控制:西门子温控模块自动控温,精度&plu***n;1℃
Temperature controlling: Siemens automatic temperature control thermostat module, precision &plu***n;1℃
4.产品范围:根据客户要求定做任意尺寸模具
Products: custom mold to any size according to customer requirements.
5.产品固定方式:模具固定(模具按客户需求订制)
Fixture method : module fixture(customized)
6.模具材质及精度:烫金板,平面度0.02mm
Mold material and precision: bronzing plate flatness 0.02mm
7.机壳材质:冷板
Equipment cover material: cold board.
8.运动部件:精密导轨
Running part: precise guide rail
9.运行速度:无级变速
Running speed: CVT
10.外形尺寸:(约)长900mm×宽640mm×高1050mm
Dimensi***: approx. L900mm*W640mm*H1050mm
11.主电源规格: AC 220V&plu***n;10%,50Hz,1.5kW
Power : AC 220V&plu***n;10%,50Hz,1.5kW
12.机身重量:60kg
Weight: 60KGS
五、各部件的工作 Each parts working
设备主要由PLC与触摸屏控制,可控制运行速度,温度调节,设备复位等动作和参数; 57步进电机带动丝杠滑块匀速运动,控制分屏机构掀起;真空泵在工作完成吸屏动作,使得屏幕平稳脱离。The equipment is mainly controlled by PLC and touch screen, you can control the speed, temperature control, equipment and reset acti*** and parameters; 57 stepper motor driven screw slider uniform motion, split-screen control mechani*** off; vacuum suction screen at the completion of the action, making ***ooth out the screen.
1.工作原理Working principle
手机屏幕在预热区充分预热大约3到5分钟,使得贴合胶融化,便于脱离。预热完毕后放置分离工作区,参数设定,行程分三段,每段速度不一,完成后,开始分离。分离机构,电机带动丝杆,滑块推进使分屏机构上模逐渐上升,屏幕外框与其一起上升,实现屏幕脱离。Phone screen fully preheated in a preheating zone of about 3 to 5 minutes, so that the fitting rubber melting, easy detachment. After the warm-up is complete separation of the work area to place, parameter setting, the trip in three sessi***, each at different speeds, is completed, began to separate. Separate mechani***, motor driven screw, making split-screen slider mechani*** to promote gradual increase in the mold, the screen frame and its rise together to achieve the screen off.
2.各部件示意图Schematic diagram of each part
工作 区1 :working area1
工作区2 :working area2
触摸屏: touch screen
操作面板:Operation panel
3.工作流程Workflow
1. 把机器调至某一适合温度(不宜过高,一般75~85摄氏度***)、恒温模式下加热一定时间后进行分离;将手机屏放置在预热区,屏幕的一面贴在预热区上,大约3到5分钟。
Adjusted the machine to a suitable temperature (not too high, generally 75 to 85 degrees Celsius best), at a c***tant temperature heating modes separated some time; the phone screen placed in the preheating zone, the side of the screen attached to the pre-the hot zone, about 3-5 minutes.
2.预热完成后,将屏幕放置到分离机构的上模中,点击运行按钮。After the warm-up is complete, put the screen on the mold separation mechani***, click on the Run button.
3.分屏区开始工作,真空泵抽真空,达到真空度后,电机根据设定参数匀速运动,上模逐渐上升,屏幕开始分离。Split-screen area starts working, vacuum pump, after the vacuum level is reached, the motor according to the set parameters uniform motion, gradually rising on the mold, the screen began to separate.
4.上模达到工作高度,屏幕分离完成。
Working height reaches the upper die, the screen separation is completed.
5.机器复位后,蜂鸣器闪烁报警三次,提示工作完成,掀开上模,取出分离的屏幕。分离后,用专用除胶剂除胶,再用清洗剂清洗干净;
After resetting the machine, flashing alarm buzzer three times, suggesting that work is completed, opened on the mold, remove the separation of the screen. After separation, with a special addition to glue than plastic, and then cleaning agent to clean;
