书刊装订设备的操作及更换零部件折卸方法 Testing and running
1．安全操作注意事项 Notice of safety operate
1.2 了解机器各部分的作用和潜在***区域，知道必要的安全措施。
Understand the role of the various parts of the machine and potentially dangerous areas, and know the necessary safety measures
1.3 启动机器前，检查机器各手柄，按钮是否处于预定的工作位置。
Before starting the machine, check the handle of the machine and whether the button is in the intended working position.
1.4 如果书刊装订设备作时突然停止，不要马上重新启动，应该按下“总停”自锁按钮，检查停机原因，待故障排除后方可重新启动。 If the machine suddenly stops working, do not restart immediately, you should press the "total stop" self-locking button, check the cause of the shutdown, to be troubleshooting before you can restart.
1.5 不允许在书刊装订设备运转时，维护运动零部件和靠近运动零部件的其他零部件。 It is not permissible to maintain moving parts and other parts near moving parts while the machine is running.
1.6 大面积***或修理时，必须按下“停止”自锁按钮，切断所以电源、气源。Large area maintenance or repair, you must press the "stop" self-locking button, cut off the power supply, gas source.
1.7 书刊装订设备在进行调整、***和修理工作时，不得使用不适当的工具。工作完毕后必须清理检查机器上的工具和其他杂物，以免发生故障。 Undue tools should not be used for adjustment, maintenance and repair work. After the work must be cleaned to check the tools and other debris on the machine, so as to ***oid failure.
1.8 在重新启动机器前，应检查所有安全设施是否处在正常位置，是否紧定，注意机器周围的其他人员是否处在安全的位置。 Before restarting the machine, check that all safety devices are in their normal position, are they tightened, and that the rest of the machine is in a safe place.
1.9 保持书刊装订设备和周围环境的清洁，及时清除掉落在地板上的油污，清理工作区的工具、抹布及碎纸废料等。 Keep the machine and the surrounding environment clean, remove the oil on the floor in a timely manner, clean up the work area of the tools, rags and shredded scrap.
1.10 及时维护、更换已失效和损坏的装置，及时报告机器发生的问题。Timely maintenance, replacement of failure and damage to the device, the timely report of the machine problems.
书刊装订设备收放物料装置的调整 Adjust the feed and receive belt
2.1 上料装置的调整 Adjust the feed belt
该工位可根据产品的宽窄来调节输送料道的宽度，松开护罩1的固定螺丝123，然后根据产品的需要调整料道的宽窄。The position of the station can be adjusted according to the width of the product to adjust the width of the conveyor material, refer to (Picture 9) to release the cover screw 1 123, and then adjust the width of the material according to the needs of the material.
2.2书刊装订设备收料装置的调整 Adjust the receive belt
该工位主要是配合主机完成收料工作，可根据主机的装订速度自动调整线体的每次位移. The station is mainly with the host to complete the receipt work, according to the host's binding speed automatically adjust the line of each displacement.
3. 书刊装订设备推刀调试 Test push knife
根据产品大小的需要，可通过调节推刀组的固定螺丝的安装位置来调节T的宽度（见图十）Depending on the size of the product, the width of the T can be adjusted by adjusting the mounting position of the setscrews' fixing screws (Picture 10)
4.书刊装订设备机器手送料系统的调整 Adjust the feed system
北京市 广东省 山东省 江苏省 河南省 上海市 河北省 浙江省 香港特别行政区 陕西省 湖南省 重庆市 福建省 天津市 云南省 四川省 广西壮族自治区 安徽省 海南省 江西省 湖北省 山西省 辽宁省 台湾省 黑龙江 内蒙古自治区 ***特别行政区 贵州省 甘肃省 青海省 新疆维吾尔自治区 西藏区 吉林省 宁夏回族自治区